volkswagen special tool vw tools volkswagen special tool volvo tool -- mmk4mkt

Headbolt & Drain Plug Socket Set 2 28.00

Drain Plug Socket
Plus Heabolt Tool
Details: Tamperproof Transmission Drain Plug Socket.
Triple Square (12 Point XZN)
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Plus Audi Headbolt Tool
Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Set of 2 Audi Tools from ZDMAK

Dont hesitate...these are BOTH the CORRECT tools for the job!

Valve Tool for Volkswagen 61.95

Valve Tool for Volkswagen Valve Tool for VolkswagenThis unique tool has been designed to allow removal and installation of valve springs while the engine is still in the carType I, II III engines 40 HP and laterThis set will also remove springs on disassembled engines.

Spark Plug Boot Tool 32.99
Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket...SOME APPLICATIONS INCLUDE: 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.
read more:

Press tool 401 0.00
High Quality German Made
Volkswagen Press Tool for assembly work.
Original Factory Tool.
read more:

VW428A 49.99
Volkswagen 428a FACTORY TOOL MADE IN GERMANY

In Stock Now!
Call if you need more info on this tool.
read more:

Brake Tool 25.00

NUMBER 3289Brake Release Tool Volkswagen VR6 JettaTool is used to disconnect brake pedal from booster.This is an Original VW Factory ToolMade in Germany for Volkswagen By Kukko*

36mm Flare Wrench 42.50
Special 36mm Flare Wrench like vw 179.Oil Line 12 Point Wrench for servicing Oil Lineson most 1977 and Later Porsche 911 and 944 Turbo.This tool is also used for adjusting rear suspension heighton 77 and Newer Porsche 911and for camber on most late model Volkswagen Bug.
read more:

Audi Headbolt Tool 17.50

This is the tool you are looking for!
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Triple Square Drain Plug Tool 49.50

This is a Special Tamperproof * Transmission Drain Plug Socket. Triple Square ( 12 Point XZN 16) Same as old Volkswagen Tool 3357. (Number 3357 is still found in many/most manuals for this job)
Applicable Porsche Boxster and Audi A4 A6 and Passat. This is an excellent high quality tool Made in Germany. Plug not included, picture is for reference only.

B90 for Volkswagen and Audi 377.00
Designed to accurately and efficientlyExtract or Install Hubs and Wheel Bearings of spindle assemblies.Applicable: All Front wheel drive VW (Water cooled) and Audifrom early 1970 to present with S.R.W.B. and I.F.S. including A.W.D.Pictures are for reference only. This is the Volkswagen Audi Kit. The Volkswagen kit "only" available below.
read more:

Drainplug Tool on Sale! 14.99

Drain Plug Socket
This is a Special Tamperproof Transmission Drain Plug Socket.
Triple Square ( 12 Point XZN )
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Headbolt Socket 17.50

This is the tool you are looking for.
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

New Style Headbolt Polydrive 17.50

This is the tool you are looking for!
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen AudiV6 and 4 Cylinder5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Audi Headbolt Toolt 17.50

Radio Removal Set 24.99

Set of Volkswagen Audi Radio Removal Tools Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
PLUS * Set Number vw 3316 Radio Removal Tools New Body Style Passat Jetta Golf Please check your manuals for details.
You will get virtually full VOLKSWAGEN coverage with this set
Plus BMW Radio Removal Tool.Pentagon shaped tool with 3 5/8 inches overall length.Applicable: Most BMWs.This Five sided driver is used to release anti theft radio mounts.YOU ALSO GET THE SPECIAL SMALL ALLEN (Right) side of picture FOR NEWER E38 & E39 7 SERIES
Plus * MERCEDES RADIO REMOVAL KEYS FOR NEWER AND OLDER VEHICLES

Oil Seal Tool 42.50
Porsche Volkswagen Tool like 204BUsed for proper installationof oil seal on flywheel side of crank shaft. All VW Boxer 4.
read more:

Super Duty Headbolt Tool 37.50

Headbolt Tool ....Read:
Same as Number T10070
Super Strong Headbolt Tool 1/2 Drive
(notice the solid one piece design)
Tool used to remove and install cylinder headbolts. New "Stronger" One Piece design. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2" Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socket The old tool number was 3452 and is now discontinued.. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. The German Tool Books call this a Polydrive. This is NOT a Torx socket although it is a 6 point tool. The points are more flat (squared off) than a torx. and it is NOT a XZN (tri square) Socket.

Complete VW Audi Radio Keys 24.99

Spark Plug Boot Tool 24.99

Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket on 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.

Best Quality XZN Size M16 49.50

This is a Special Tamperproof Transmission Drain Plug Socket. Triple Square ( 12 Point XZN 16) Same as old Volkswagen Tool 3357. (Number 3357 is still found in many/most manuals for this job)
Applicable Porsche Boxster and Audi A4 A6 and Passat. This is an excellent high quality tool Made in Germany.
* Plug not included, picture is for reference only.

Tri Square Drain Plug XZN 49.50

Thin Head Flexible Ratchet 79.99
Ever see this one? It is a Super Tool....
A flexible "Thin Head" Reversible bit holding Ratchet.
(the reverse mechanism is on the flip side of photo not shown)
The head will flex backwards forwards more than a 90 degree (70 to 80)
The thickness of the head is 10mm
The overall length is 164mm ( 6 1/2 inch).
This tool is great for getting into a tight spot with a special bit,
during rare or difficult procedures (bits not included)
Call if you are looking for a special bit to go with the tool.
read more:

Volkswagen Door Tool 9.99

T10011Volkswagen Door Tool triple Square 4
This is the correct tool for the job
New Beetle Tool This tool is used for R & R of door handle screws.Applicable: 1998 & newer VW Golf, Jetta, Passat & New Beetle....possibly other VW Audi.
This tool is a high quality item you will like.

Special Rivet Tool 0.00
Special Rivet Tool
Plier with 90 degree rotating head.
Tool used to remove two piece reusable plastic rivets
found on door panels, engine shields, wheel well shields etc.
For undivided rivets the Plier can also be used for cutting the head off the rivet.
Easy to use universal Plier eliminates damage to trim and door facings.
read more:

Crankshaft Gear Puller Volkswagen 86.50

Crankshaft Gear Puller for Volkswagen This inexpensive tool solves the problem of removing the crankshaft timing gear, a gear which must be removed when an engine is rebuilt and the main bearings are changed. In operation, this tool simply slips under the gear and with a twist of a wrench the gear is easily removed. The highest quality standards are used in the construction of this tool for years of repair shop service. To prevent damage to the end of the crankshaft, a ball bearing swivel is used, while for strength, the griping shoe is made of forged steel. For use on all type I, II, & III engines 40hp and later.

17 x 17 Injection Wrench 39.50
Double Ended Flare Nut Box Wrench Size 17 x 17mmOverall Length 241mm (9.5 inch)For injection pipes on Volkswagen / Audi This tool will help you when you remove and install the fuel lines from the injection pump and the injectors themselves.For TDI: You will still need to torque the 17mm fittings down to spec, but this tool will make taking the fittings off a snap, as well as putting them back on.This is a Factory Tool Made in Germany
read more:

Headbolt Tool Set 2 29.50

These are the tools you are looking for!
Plus they are on sale!
Headbolt Tools 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi
Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tools. Please read: The T10070 is the correct current VW Audi number for this new style tool.The old tool number was 3452 and is now discontinued.Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this new style a Polydrive.

Plus you get Headbolt Tool Triple Square 12 Point (XZN) Socket M10Sturdy 1/2 Drive Tools used for a wide variety of applications including headbolts.Excellent for working on German vehicles.
This XZN tool is 5 1/2 inches long and the shaft is 4 inches.
Super set for removing & installing cylinder headbolts on both early and late model 1.8T and 2.0L gas engines. You will get both tools with this purchase.

Audi VW Headbolt Tool Set 2 29.50

These are the tools you are looking for!VW AUDI Headbolt Tools 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi
Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tools. Please read: The T10070 is the correct current VW Audi number for this new style tool.The old tool number was 3452 and is now discontinued.Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this new style a Polydrive.

Plus you get Headbolt Tool Triple Square 12 Point (XZN) Socket M10Sturdy 1/2 Drive Tools used for a wide variety of applications including headbolts.Excellent for working on German vehicles.
This XZN tool is 5 1/2 inches long and the shaft is 4 inches.
Super set for removing & installing cylinder headbolts on both early and late model 1.8T and 2.0L gas engines. You will get both tools with this purchase.

Volkswagen Filler Tool 5.99
NUMBER VW170Tool is for Air Cooled VW repair,and is designed to remove and installthe nut that holds the oil fillerand breather tin to the generator stand. Designed to snap over a 1/2 drive extension,this tool easily reaches down into the oil fill,to remove or tighten the hard to get at retaining nut.
read more:

Optical Tester Made in Germany 0.00
Super Optical Tester
Cooling System Special Tool
Hazet 4810 Made in Germany
for controlling the anti freezing acid concentration
in the cooling system, as well as for cooling fluid G11 and G12
VOLKSWAGEN/AUDI and the battery acid concentration (battery charging).
read more:

Pin Wrench 37.00

Heavy Duty Tensioner with Handle Grip
Same as Volkswagen number T10020
VW AUDI TENSION PULLEY SPANNER WRENCH This unique tool is for 1998 and later VW and Audi which require spanner wrench adjustments to the timing belt.Details: Special Wrench for adjusting the belt tension on the following: Audi: A6 1.6 (96 and newer) ALZ VW: Polo Classic, Golf, Bora, New Beetle 1.6 (97 ) AEH / AKL / APF / AUR /AVU / AYD Golf, Bora, New Beetle, 2.0 (98 ) AQY / APK

This is the new style Pin wrench with the (offset) angled head, same as the factory tool only this tool is a little longer for leverage with a rubber handle grip for a better feel compared to the smaller version.

T45 Torx with U Joint 14.99

Torx size T45 Universal Joint Special Tool Torx T45 used for upper door hinge and other applications.VW Volkswagen Audi repair.Satin Chrome plated 3/8 drive

Super Duty Pin Wrench 37.00

Pinion Nut Cone 69.50
Like Volkswagen Tool 381/14Pinion Nut Cone Socket Cone shaped Socket with 1/2" drive.This tool is used for R&R of grooved nutwhich retains pinion bearing within its housing.Applicable: Early VW air cooled models.
read more:

Cylinder Head Tool Kit 23.50
Cylinder Head Alignment Kit Same as Volkswagen Tool 3070
Set comes with (2) pairs of guide pins, 11X1.75mm and 12X1.75mm.VW model Scirocco, Rabbit, Dasher, Fox. Audi model 4000, 5000
read more:

Threaded Pin for T.D.C. 25.00

Locking Pin
TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6
For installing or removing toothed belt /flywheel drive plate.

Bar and Pin for 5 Valve 139.50

Camshaft Timing Tool Set (2)
TOOL REF 3391
Cam/Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 2002 4 cam.

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6Please note: 3391 for 5 valves per cylinder.

Holding Tool and Wrench Set 49.99

Set of 3 Includes:
Double Waterpump Tool*
This special tool covers most popular applications
Used for securing Water Pump Hub from rotating during R & R of Fan Clutch Nut
Applicable:M10, M20, M30, M40, M41, M42, M50, M60, M62

Plus
2 Long Pattern Thin Wrenches
German Car Special Tools
One of each size: 36mm and 32mm
Overall length of 15 inches.
Thickness of each wrench is 8mm.

Valve Spring Tool & Bridge 142.50

Valve Tools (2)
Set including:Valve Spring Compressor Bar
Same as Volkswagen Tool Number VW 541/1
Used for R&R of valve spring or rocker armWith this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool BridgeApplicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker armUsed in conjunction with tool VW541/1Applicable: Model 924. VW / AUDI 4 5 Cyl.

Valve Spring Tool and Bridge 142.50

Valve Spring Tools Set including:VA6010Valve Spring Compressor BarSame as Volkswagen Tool Number VW 541/1Used for R&R of valve spring or rocker armWith this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool BridgeApplicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker armUsed in conjunction with tool VW541/1Applicable: Model 924. VW / AUDI 4 5 Cyl.

Ferrari Head Bolt Tool 44.00
Special 8 Point
Offset ring Wrench for Headbolts.
Available 15mm or 17mm both come 1/2 inch drive.
The overall length of the tool will be 274mm.
read more:

Audi VW Headbolt Tool 32.99

Polydrive Cylinder Head Socket for VW/Audi.
This fits in the new special profile. Ref: Volkswagen number T10070.
This is not a torx and it is not a cheesehead or triple square. This is called Polydrive.
The overall length is 168mm. Shaft length is 130.
Super High Quality Tools Made in Germany by Hazet!

Special Tool for Subaru 35.50

Special Tool for Subarus with 5mm square drive valve adjustment screws with a 12mm jam nut. This two in one tool features a window in the 12mm socket so the technician can see the position of the 5mm socket while it holds the adjustment screw as the 12mm jam nut is tightened. The handle pivots from one side to the other, so the window is always possible.

Power Steering Waterpump Pulley Tool 24.00

VA6024Power Steering and Waterpump Pulley Removal & Replacement Tool Volkswagen AudiUsed to hold the power steering or water pump pulley stationarywhile removing or replacing the three socket headbolts that attach pulley to the shaft.Tool is designed to be used on pulleys that utilize these socket head bolts.Applications:VW Audi 4 cylinder water cooled gas or diesel engines from 1975 to current.Volkswagen V6 1992 and newer.Audi power steering pump pulley V8 1990 and newer.Audi V6 1992 to current.Also VW 1983 to 1988 and Audi 1981 to 1995 with socket head boltsholding the pulley to power steering pump.

Triple Square Socket 3357 14.99

Drain Plug Socket
This is a Special Tamperproof Transmission Drain Plug Socket.
Triple Square ( 12 Point XZN )
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Triple Square Socket for Transmission 28.50

Drain Plug Socket:This is a Special Tamperproof * Transmission Drain Plug Socket.Triple Square ( 12 Point XZN ) Same as Volkswagen Tool 3357.For Porsche Boxster and Audi A4 A6 and Passat.This is an excellent "Stronger One Piece" design.

Flywheel Lock 00
Universal Flywheel Lock
Designed for use on all air cooled Volkswagen engines
Type 1, 2, 3, & 4 and on all air cooled Porsche engines
(series 356, 912, 914, & all 911s through 1969).
This tool is a must when changing a flywheel or its seal
and it comes in handy when changing a clutch.
Made from a forging, this quality tool will last a lifetime.
read more:

Special Hook 3370 29.99
Factory Tool 3370
Made in Germany.
TOOL USED TO REMOVE FRONT SEAT BACK REST PANEL ON AUDI A4.
read more:

27mm Special Socket 82.98

27mm Special Tool Made in Germany
12 Point Open Socket (1/2 Drive size) Tool used for injection nozzles on BMW Diesel
E30=324TD
E28=524TD
E34=524TD
M51=E36=325TD
E34=525TDS
This Tool is very hard to find and the German Hazet quality cant bebeat. You can find all the other sizes but a 27mm is very difficult to locatewhen you are in a pinch. Ref BMW 135320

B90 for Volkswagen Audi 377.00

Designed to accurately and efficientlyExtract or Install Hubs and Wheel Bearings of spindle assemblies.Applicable: All Front wheel drive VW (Water cooled) and Audifrom early 1970 to present with S.R.W.B. and I.F.S. including A.W.D.Pictures are for reference only. This is the Volkswagen Audi Kit. The Volkswagen kit "only" available below.

You Searched for

volkswagen special tool

Trade Links With ZDMAK