volkswagen 3243 SARASOTA volkswagen 3243 spark plug tool -- mmk4mkt

36mm Flare Wrench 42.50
Special 36mm Flare Wrench like vw 179.Oil Line 12 Point Wrench for servicing Oil Lineson most 1977 and Later Porsche 911 and 944 Turbo.This tool is also used for adjusting rear suspension heighton 77 and Newer Porsche 911and for camber on most late model Volkswagen Bug.
read more:

Brake Caliper Rewind Set 47.99
U.S./EURO/ASIAN/4WD VEHICLES
Disc Brake Pad & Caliper Service Tool Kit
Includes 8 adapters Magnetic socket adapter.
For brake assemblies
For rotating pistons back into caliper to provide clearance for new pads
Prevents damage to the piston and bootDesigned for use with Mercedes, BMW, Volkswagen, GM, Audi, Ford,Honda, Subaru, Mazda, Nissan, Mitsubishi, Toyota, Land Rover and 4 wheel drive vehicles.Blow molded carryingcase for easy storage.
read more:

Flywheel Lock 00
Universal Flywheel Lock
Designed for use on all air cooled Volkswagen engines
Type 1, 2, 3, & 4 and on all air cooled Porsche engines
(series 356, 912, 914, & all 911s through 1969).
This tool is a must when changing a flywheel or its seal
and it comes in handy when changing a clutch.
Made from a forging, this quality tool will last a lifetime.
read more:

Flywheel Lock 22.95
215 Volkswagen Porsche Tool
Flywheel Lockused to secure the crankshaft from rotating during R&R of motor.
Used in conjunction with Engine Holding Fixture P201,
where Flywheel Lock bolts into a machined channel.
All Porsche and VW 6V or 12V, air cooled.Please note: This item is included in the complete kit also.
read more:

Heavy Duty Bench Clamp 187.50
313 Volkswagen Porsche Tool Designed for to securely carry the full weightof an air cooled twin turbo Boxer 6Tool Number VW 313Properly suited for a work bench.
read more:

Oil Seal Tool 42.50
Porsche Volkswagen Tool like 204BUsed for proper installationof oil seal on flywheel side of crank shaft. All VW Boxer 4.
read more:

Pinion Nut Cone 69.50
Like Volkswagen Tool 381/14Pinion Nut Cone Socket Cone shaped Socket with 1/2" drive.This tool is used for R&R of grooved nutwhich retains pinion bearing within its housing.Applicable: Early VW air cooled models.
read more:

Press tool 401 0.00
High Quality German Made
Volkswagen Press Tool for assembly work.
Original Factory Tool.
read more:

Valve Adjustment * Deep Offset Wrench 5.99
German MadeDeep Offset 12 Point Spanner.This Exact item is no longer available from Germany.PORSCHE VW VALVE ADJUSTMENTTYPE 1, 2, 3 and 4 VOLKSWAGEN
read more:

Volkswagen Filler Tool 5.99
NUMBER VW170Tool is for Air Cooled VW repair,and is designed to remove and installthe nut that holds the oil fillerand breather tin to the generator stand. Designed to snap over a 1/2 drive extension,this tool easily reaches down into the oil fill,to remove or tighten the hard to get at retaining nut.
read more:

VW428A 49.99
Volkswagen 428a FACTORY TOOL MADE IN GERMANY

In Stock Now!
Call if you need more info on this tool.
read more:

92mm Oil Wrench Socket 38.00

92mm Oil Filter Wrench
Will fit all Mann Knecht filters that require (92mm) and 15 inside flats.
Original Factory Tool Made in Germany. Size 92mm.
With outer (top) square drive size 12.5mm = 1/2 inch for ratchet or socket, or use the outside hex 27mm with a wrench.
15 point (inside flats or flutes).
Excellent high quality tool.
This tool will fit many (92mm) Volkswagen Audi Diesels.

Brake Caliper Rewind Set 49.50

U.S./EURO/ASIAN/4WD VEHICLES
Disc Brake Pad & Caliper Service Tool Kit
Includes 8 adapters Magnetic socket adapter.
For brake assemblies
For rotating pistons back into caliper to provide clearance for new pads
Prevents damage to the piston and bootDesigned for use with Mercedes, BMW, Volkswagen, GM, Audi, Ford,Honda, Subaru, Mazda, Nissan, Mitsubishi, Toyota, Land Rover and 4 wheel drive vehicles.Blow molded carryingcase for easy storage.

Long Pattern Hex Set 4 13.50

4 Pc Long Allen Hex Set
Sizes include: 6, 7, 8, and 10mm Hex.
This set works well on several vehicles such as Audi, AMC, BMW,
Honda, Jaguar, Jeep, Saab, Volkswagen and Volvo.
3/8 Drive set of 4

17 x 17 Injection Wrench 59.50

Double Ended Flare Nut Box Wrench Size 17 x 17mmOverall Length 241mm (9.5 inch)For injection pipes on Volkswagen / Audi This tool will help you when you remove and install the fuel lines from the injection pump and the injectors themselves.For TDI: You will still need to torque the 17mm fittings down to spec, but this tool will make taking the fittings off a snap, as well as putting them back on.This is a Factory Tool Made in Germany

2 Pins and 2 Plates 103.00

2 Pins and 2 Plates Set of four tools.VW Audi T.D.I. and New Beetle Cam Kit Reference numbers for the two tools on the left are: 3418 and 3359. Tool Set for factory correct and trouble free installations. This is a popular set for Diesel timing of Bosch injection pumps. This set has been developed for aligning the cam shaft with the Diesel pump on 1998 and newer VW models equipped with a T.D.I. engine. This two piece lock plate and alignment pin allows the technician for factory correct and trouble free installations.

Tools on the right side of image are Diesel Lock Plate / Cam Setting Bar Same as Volkswagen ref 2065a Tool used for securing the cam shaft from rotating and maintaining correct timing position engine AAZ during R&R of cam shaft drive belt. Applicable: VW/Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 Lock Pin for Diesel (Same as VW tool 2064). Tool used for securing Bosch diesel injection pump sprocket from rotating during R&R of cam shaft drive belt. This Locking Pin also assists in locating the general timing position of pump. Volkswagen Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 All 4 tools are High Quality Made in Europe!

3 Piece Oil Service Set 29.50

3 Piece Oil Service Set includes sizes 36mm, 32mm and 27mm 6 point sockets. (36 mm for M52, M60, M62, M70, M73 engines) Special 36mm Oil Filter Wrench Removes and installs filters on BMW Mini Cooper. The low profile socket fits 36mm fuel and oil filters. The low profile socket works in confined spaces. 3/8 in. drive Not for use with an impact wrench. BMW Mini Cooper, BMW M52 6 cylinder, BMW M60 8 cylinder, BMW M70 12 cylinder.Mercedes Benz diesel engines: OM604, OM605, OM606 (1995 W124 E300 diesel, 96 97 W210 E300 diesel, 1998 E300 turbodiesel).Same as Mercedes tool number: 606 589 01 09 00VW Volkswagen VR6 Also for Ford Truck 6.0L 03 04
Plus you get the 32mm and the 27mm.
27 mm for R&R of oil filter cartridge element.App.: M163 (Class A), C230 (Compressor)
32 mm for R&R of Oil filter cartridge element.Applicable: Opel Astra, Corsa, VW Passat, Audi.

Audi Info and Timing 0.00

There are three main Cam bars for timing.
3391, 3243 and T40005
(T40005 is for V 8)
Notice the tool number 3242 this is the T.D.C (TOP DEAD CENTER) Pin
This pin goes with 3391 or 3243.
Type your selection in the search or you can find the tools in this Audi section.
Feel free to call me or email. I will try to assist you.
Please note:
In order to make your selection you must determine if your vehicle is 2 valve per cylinder or 5 valve per cylinder or V8. Example = Notice tool number 3391 says it is for 5 valve. The 3243 is for 2 valve per cylinder.

B90 for Volkswagen Audi 377.00

Designed to accurately and efficientlyExtract or Install Hubs and Wheel Bearings of spindle assemblies.Applicable: All Front wheel drive VW (Water cooled) and Audifrom early 1970 to present with S.R.W.B. and I.F.S. including A.W.D.Pictures are for reference only. This is the Volkswagen Audi Kit. The Volkswagen kit "only" available below.

Bar and Pin for 5 Valve 139.50

Camshaft Timing Tool Set (2)
TOOL REF 3391
Cam/Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 2002 4 cam.

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6Please note: 3391 for 5 valves per cylinder.

Bonus Torx Set 26.00

Torx Bonus Set Including Screwdriver Set 7 Pc. Sizes included: T8, T10, T15, T20, T25, T27 & T30.
Torx (6 Point) heads used for a wide variety of applications and a wide variety of vehicles. Please note: The screwdrivers are not tamperproof they are standard torx. The folding unit and ratchet at the bottom of the picture are both tamperproof. The Fold up tool has Tamperproof Torx tips. Each torx blade has a hole in the tip = Tamperproof) The sizes are: T9, T10, T15, T20, T25, T27, T30, T40 Some applications include: The T25 for use on E34 E32 E36 E39 E38 (tilt slide sunroof). The T30 is for most BMW with supplemental restraint systems / SRS (BMW REF 002110). The T20 is for some applications on E38 (Diffusion Disc Mount).
Torx Combo Mini Bit and Ratchet SetThe seven bits on the left side of the bit holer are Torx TamperproofPlus this set has 1 and 2 Phillips bits, and a flat head bit.The Tamperproof Torx sizes are: T10, T15, T20, T25, T30, T40for Volkswagen, Audi,Volvo, Mercedes and BMW applications.
You will get all of the tools shown here with this purchase.

Brake Tool 25.00

NUMBER 3289Brake Release Tool Volkswagen VR6 JettaTool is used to disconnect brake pedal from booster.This is an Original VW Factory ToolMade in Germany for Volkswagen By Kukko*

Cam Bar and Pin for 2 Valve 139.50

Camshaft TimingTool Set (2)
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4  94 97 AFC Engine

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6

Please note: 3243 for 2 valves per cylinder. 

Cam Bar for 2 Valve 129.50

Camshaft Securing Bar Timing Tool
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4 94 97 AFC Engine
Please note: 3243 Securing Bar for2 valves per cylinder.

Cam Tool Puller 289.50

Volkswagen ref: T40001
First number 2510 1
Extractor (Puller)for the camshaft phasing gear with 5 and 6 spokes on 4 resp.
6 cylinder engines TDi, engines V6 and V8,
AUDI A 4, A 6, A 8
Second Item 2510 8 Extraction Hook
for the careful extraction of camshaft phasing gear with 5 spokes on VW/AUDI V8 carburetor engines.
Call if you have questions about this item.

Chain Adjuster 24.50

3366CHAIN ADJUSTER Required to change the troublesome cam adjuster seal
Audi and Volkswagen 4, 6 (2.7 and 2.8) and 8 CylWith 5 Valve per Cyl.
Also Audi VW 1.8 Golf Jetta Passat New Beetle
Note:The manual says to remove both camshafts to change the seal ...
but using this tool you can relieve the tension on the camshaft chainand lift it up far enough to clean, remove and replace the gasket and seal.
This procedure not only saves time but saves any other damagethat may happen to camshafts and bearings by removing them.
ORIGINAL MATRA FACTORY TOOL MADE IN GERMANY

CIS Injector Puller 9.99

Number 1123/4CIS Injector Puller tool used to easily remove CIS fuel injectors on many in line engines.In operation, this tool fits around the injector base and with a screwdriver(used as a lever put into the slots of the tool)simply "POP" the injector out, without damage to the injector hose.Applications include: All Gas Water Cooled Volkswagen,Porsche 924 and Audi 4000, 5000 with mechanical fuel injectors.
High quality Cis and Cis E fuel injector puller tool This is by far one of the more useful tools in the shop. If you have ever attempted the "two screwdriver technique" you will know it can be tricky. Injectors are proned to rusting when they have been in the head for a long period of time, they become lodged in there and are next to impossible to wiggle out without damaging expensive lines. This tool made of high tensile strength steel and hooks around the base of the injector; where they are intended to be pulled from.

Clutch Cable Tool 26.00

NUMBER 3151Clutch Cable Fixture Volkswagen Factory Tool Made in GermanyUsed to position the self adjusting clutch cable at transmission during assembly(Self Adjusting Clutch) GOLF JETTA SCIROCCO 1985 and Newer

Cylinder Head Tools 23.50

Cylinder Head Alignment Kit VA6000 Like Volkswagen Tool 3070 Set comes with (2) pairs of guide pins, 11X1.75mm and 12X1.75mm.VW model Scirocco, Rabbit, Dasher, Fox. Audi model 4000, 5000

Dipstick Funnel 4.99

Dipstick Funnel Volkswagen Audi used on many enines from 85 thru 99 item number 53103 663

Exhaust Clip Expander 65.00

Like old Volkswagen Ref old number 3049A Exhaust Clip Expanderor C Clip Spreader. This tool is used for the proper R&Rof exhaust manifold Spring clip. This is a Great Tool you will like and the price is right.

Exhaust Clip Expander 85.00

Like Volkswagen Tool 3049A Exhaust Clip Expanderor C Clip Spreader...This tool is used for the proper R&Rof exhaust manifold Spring clip. This is a Quality Tool and the price is right.

Headbolt & Drain Plug Socket Set 2 28.00

Drain Plug Socket
Plus Heabolt Tool
Details: Tamperproof Transmission Drain Plug Socket.
Triple Square (12 Point XZN)
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Plus Audi Headbolt Tool
Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Set of 2 Audi Tools from ZDMAK

Dont hesitate...these are BOTH the CORRECT tools for the job!

Headbolt Socket 17.50

This is the tool you are looking for.
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Headbolt Tool Set 2 29.50

These are the tools you are looking for!
Plus they are on sale!
Headbolt Tools 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi
Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tools. Please read: The T10070 is the correct current VW Audi number for this new style tool.The old tool number was 3452 and is now discontinued.Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this new style a Polydrive.

Plus you get Headbolt Tool Triple Square 12 Point (XZN) Socket M10Sturdy 1/2 Drive Tools used for a wide variety of applications including headbolts.Excellent for working on German vehicles.
This XZN tool is 5 1/2 inches long and the shaft is 4 inches.
Super set for removing & installing cylinder headbolts on both early and late model 1.8T and 2.0L gas engines. You will get both tools with this purchase.

More Tools 0.00

Be sure to look in the VOLKSWAGEN section for more tools. Plus you will find some sweet deals in the ZDMAK SPECIALS section, and in the TODAYS SPECIALS section. If you need something quickly please email or call. Expedited or Air shipments should be called in as early in the day as possible. I will do all I can to get you the tools you need or help you with your tool search.

Pin Wrench 37.00

Heavy Duty Tensioner with Handle Grip
Same as Volkswagen number T10020
VW AUDI TENSION PULLEY SPANNER WRENCH This unique tool is for 1998 and later VW and Audi which require spanner wrench adjustments to the timing belt.Details: Special Wrench for adjusting the belt tension on the following: Audi: A6 1.6 (96 and newer) ALZ VW: Polo Classic, Golf, Bora, New Beetle 1.6 (97 ) AEH / AKL / APF / AUR /AVU / AYD Golf, Bora, New Beetle, 2.0 (98 ) AQY / APK

This is the new style Pin wrench with the (offset) angled head, same as the factory tool only this tool is a little longer for leverage with a rubber handle grip for a better feel compared to the smaller version.

Power Steering Waterpump Pulley Tool 24.00

VA6024Power Steering and Waterpump Pulley Removal & Replacement Tool Volkswagen AudiUsed to hold the power steering or water pump pulley stationarywhile removing or replacing the three socket headbolts that attach pulley to the shaft.Tool is designed to be used on pulleys that utilize these socket head bolts.Applications:VW Audi 4 cylinder water cooled gas or diesel engines from 1975 to current.Volkswagen V6 1992 and newer.Audi power steering pump pulley V8 1990 and newer.Audi V6 1992 to current.Also VW 1983 to 1988 and Audi 1981 to 1995 with socket head boltsholding the pulley to power steering pump.

Puller 84.00

Puller Same as Volkswagen Tool 3032 Injection Pump ToolUsed for the proper extraction of injection pump drive gear.Applicable:VW Audi diesels *Excluding TDI

Radio Removal Set 24.99

Set of Volkswagen Audi Radio Removal Tools Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
PLUS * Set Number vw 3316 Radio Removal Tools New Body Style Passat Jetta Golf Please check your manuals for details.
You will get virtually full VOLKSWAGEN coverage with this set
Plus BMW Radio Removal Tool.Pentagon shaped tool with 3 5/8 inches overall length.Applicable: Most BMWs.This Five sided driver is used to release anti theft radio mounts.YOU ALSO GET THE SPECIAL SMALL ALLEN (Right) side of picture FOR NEWER E38 & E39 7 SERIES
Plus * MERCEDES RADIO REMOVAL KEYS FOR NEWER AND OLDER VEHICLES

Red X Dog for Volkswagen Audi 189.99

ZDMAK D023XREDXDOG LITEOFF One of the most popular versions ofVAG (VW/Audi/Seat/Skoda/Ford) reset tool.First, it provides you with the capability of resetting the oil serviceand inspection service reminder displays. In addition, you can also reset all fault codes,(both those with and without a dashboard indicator) on all vehicle systems.Applicable: All vehicles with digital diagnostic systems.

Set 3 Audi Clutch Tools 13.99

Set of 3
Audi Clutch Alignment Tools
Covers a BIG variety of Audi (and many Volkswagen Applications).
The clutch tools in this kit are extremely durable long lasting and inexpensive.
These tools can be used over and over again.
A must for clutch repair shop, clutch specialist, transmission repair shops,
automotive stores, school shop classes, clutch resellers,
foreign and domestic repair shops.
Readmore about this 3 piece Click Here

Spark Plug Boot Tool 24.99

Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket on 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.

Spreader 28.99

SPREADING TOOL5TH GEAR LOCK PLATE 020 TRANSMISSION Ref: Volkswagen Tool 3097

T45 Torx with U Joint 14.99

Torx size T45 Universal Joint Special Tool Torx T45 used for upper door hinge and other applications.VW Volkswagen Audi repair.Satin Chrome plated 3/8 drive

Threaded Pin for T.D.C. 25.00

Locking Pin
TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6
For installing or removing toothed belt /flywheel drive plate.

Triple Square Drain Plug Tool 49.50

This is a Special Tamperproof * Transmission Drain Plug Socket. Triple Square ( 12 Point XZN 16) Same as old Volkswagen Tool 3357. (Number 3357 is still found in many/most manuals for this job)
Applicable Porsche Boxster and Audi A4 A6 and Passat. This is an excellent high quality tool Made in Germany. Plug not included, picture is for reference only.

Triple Square Socket 3357 14.99

Drain Plug Socket
This is a Special Tamperproof Transmission Drain Plug Socket.
Triple Square ( 12 Point XZN )
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Triple Square Socket for Transmission 28.50

Drain Plug Socket:This is a Special Tamperproof * Transmission Drain Plug Socket.Triple Square ( 12 Point XZN ) Same as Volkswagen Tool 3357.For Porsche Boxster and Audi A4 A6 and Passat.This is an excellent "Stronger One Piece" design.

Valve Adjustment * Deep Offset Wrench 6.99

German MadeDeep Offset 12 Point Spanner.This Exact item is no longer available from Germany.PORSCHE VW VALVE ADJUSTMENTTYPE 1, 2, 3 and 4 VOLKSWAGEN

You Searched for

volkswagen 3243

Trade Links With ZDMAK