toyota special tool SARASOTA toyota special tool toyota repair tool -- mmk4mkt

Toyota Bonus Set 37.99

ZDMAK SPECIAL DEAL
Headbolt tool and Valve tools...
First Item: Valve tool designed to allow for easy valve adjustment on most Toyota overhead cam engines using spacer shims for valve adjustment. In operation, the tip of the pliers pushes between the spacer shim and the camshaft as the pliers are squeezed close. This action moves the shim and its valve lifter down from the camshaft lobe. In the down position the separate wedge tool is placed between the valve lifter ledge and the camshaft. This wedge tool then maintains a gap between the shim and the camshaft as the pliers are removed. The spacer shim can then be removed through this gap and replaced with one of the correct thickness. Works especially well with 3S FE and 3S GELC Toyota DOHC.Toyota number 09248 55040For Camry, Sienna, Avalon, Solara, Supra, 4Runner, MR2, Previa, Paseo, Tacoma, Tercel, T100, Celica.Packaged as shown with pliers and spacer wedge. Does not work with Land Cruiser 1993 1997 and Lexus LX400 1994 199

PLUS * Toyota Headbolt Tool
12 Point (Triple Square) Socket.
This item is called XZN (style) and is very hard to find. 1/2 Drive Socket is 100mm long, for easy access to hard to reach headbolts.

Toyota / Asian Oil Seal Bonus Kit 159.50

Universal Asian Oil Seal Installation Bonus Kit
This special kit was designed for the proper installation of crank shaft oil seals, situated within confined areas on most 4, 6 and 8 cyl Toyota, Lexus, Nissan, Mitsubishi, Mazda and Infiniti.Application includes camshaft oil seal installation of Toyota Lexus 2.5L, 2.8L, 3.0L, 3.4L, 4.0L & 4.3L The stepbolts screw into the cam or crankshaft end. The press nut and washer allows for an even pressing force, seating the oil seal into the engine case with ease.

See tool TOY100 for 4 cylinder Asian camshaft oil seal installation. Honda Acura, see tool HO100, HO105, HO115, and HO115 WB.

Toyota Master Set 99.99

ZDMAK THREE ITEM MASTER KIT FOR TOYOTA
Cam Tool Plus Headbolt tool Plus Valve Tool
You can read about all three of these items on this page (above). This set includes item numbers TOY4VT, plus TOYHB and 2705.

Oil Seal Installation Bonus Kit 159.50

Toyota Valve Adjustment Tool 19.99

This tool has been designed to allow for easy valve adjustment on most Toyota overhead cam engines using spacer shims for valve adjustment. In operation, the tip of the pliers pushes between the spacer shim and the camshaft as the pliers are squeezed close. This action moves the shim and its valve lifter down from the camshaft lobe.In the down position the separate wedge tool is placed between the valve lifter ledge and the camshaft. This wedge tool then maintains a gap between the shim and the camshaft as the pliers are removed. The spacer shim can then be removed through this gap and replaced with one of the correct thickness.
Works especially well with3S FE and 3S GELC Toyota DOHC.
Toyota number 09248 55040
For Camry, Sienna, Avalon, Solara, Supra, 4Runner, MR2, Previa, Paseo, Tacoma, Tercel, T100, Celica.
Packaged as shown with pliers and spacer wedge.Does not work with Land Cruiser 1993 1997 and Lexus LX400 1994 1997

Toyota Transmission Tool 19.50

Puller used for the proper extraction of front counter shaft bearing.Applicable: Toyota transmission L52 81 83 5speed /4WD

Toyota Transmission Tool 28.00

Puller used for the proper extraction of rear counter shaft bearing and 5th gear. Applicable: Toyota transmission L52 81 83 5speed 4WD.

Toyota Lexus Cam Tool Kit 58.00

Cam Seal Installer w/ 10 & 12mm X 12.5 Threaded Cam Bolts Features and Benefits: This tool is designed to easily install the cam seals in 4 & 6 cylinder engines for Mazda, Nissan & Toyota/ Lexus engines that have 10 & 12mm x 1.25 cam bolts. These engines are mounted transversely which puts the camshaft end in very close proximity to the shock tower making replacement of the cam seal extremely difficult using conventional methods. Simply screw the threaded rod into the cam end, slide the body over the rod against the seal and press in the seal using the nut provided. This tool comes in black finish.

Thin Head Flexible Ratchet 79.99
Ever see this one? It is a Super Tool....
A flexible "Thin Head" Reversible bit holding Ratchet.
(the reverse mechanism is on the flip side of photo not shown)
The head will flex backwards forwards more than a 90 degree (70 to 80)
The thickness of the head is 10mm
The overall length is 164mm ( 6 1/2 inch).
This tool is great for getting into a tight spot with a special bit,
during rare or difficult procedures (bits not included)
Call if you are looking for a special bit to go with the tool.
read more:

Special Rivet Tool 0.00
Special Rivet Tool
Plier with 90 degree rotating head.
Tool used to remove two piece reusable plastic rivets
found on door panels, engine shields, wheel well shields etc.
For undivided rivets the Plier can also be used for cutting the head off the rivet.
Easy to use universal Plier eliminates damage to trim and door facings.
read more:

Toyota Locknut Tool 19.99

Toyota front wheel bearing design change requires a new procedure to remove the locknut: The free wheel hub assembly locknut is on the inside, so the hub must be removed to gain access. This wrench has a four pin design accommodates the four holes in each locknut, which prevents slippage under high torquing requirements. Works on 1995 and newer Tacoma, and 1996 and newer T100 and 4Runner.

Holding Tool and Wrench Set 49.99

Set of 3 Includes:
Double Waterpump Tool*
This special tool covers most popular applications
Used for securing Water Pump Hub from rotating during R & R of Fan Clutch Nut
Applicable:M10, M20, M30, M40, M41, M42, M50, M60, M62

Plus
2 Long Pattern Thin Wrenches
German Car Special Tools
One of each size: 36mm and 32mm
Overall length of 15 inches.
Thickness of each wrench is 8mm.

Push Pin Pliers Set of 2 39.50

PUSH PIN REMOVAL PLIERS SETPush pin pliers are designed to remove plastic push pins onHonda, Toyota, GM, Saturn and many other vehicles.Special ground tips remove the pins without damage.Pliers can also be used to remove U Joint circle clips.One tool with a 75 degree offset head to allow push pin removal in tightareas. These tools will save you time and headaches.

Ferrari Head Bolt Tool 44.00
Special 8 Point
Offset ring Wrench for Headbolts.
Available 15mm or 17mm both come 1/2 inch drive.
The overall length of the tool will be 274mm.
read more:

M9 Toyota Headbolt Tool 14.99

Size M9 XZN (Triple Square) 12 Point Socket. This item is called XZN (XZN means the tool has 12 points) and is very hard to find in this size.The is bigger than 8mm and smaller than 10mm. The 8 and 10 are relatively easy to find. This size is not. This tool is 100mm long, allowing for easy access to hard to reach headbolts.

Special Tool for Subaru 35.50

Special Tool for Subarus with 5mm square drive valve adjustment screws with a 12mm jam nut. This two in one tool features a window in the 12mm socket so the technician can see the position of the 5mm socket while it holds the adjustment screw as the 12mm jam nut is tightened. The handle pivots from one side to the other, so the window is always possible.

Toyota Crank Seal Installer 41.50

For the proper and easy installation of oil sealon pulley side of the crankshaft.Applicable: Most 4 & 6 cylinder Toyota engines

Special Hook 3370 29.99
Factory Tool 3370
Made in Germany.
TOOL USED TO REMOVE FRONT SEAT BACK REST PANEL ON AUDI A4.
read more:

27mm Special Socket 82.98

27mm Special Tool Made in Germany
12 Point Open Socket (1/2 Drive size) Tool used for injection nozzles on BMW Diesel
E30=324TD
E28=524TD
E34=524TD
M51=E36=325TD
E34=525TDS
This Tool is very hard to find and the German Hazet quality cant bebeat. You can find all the other sizes but a 27mm is very difficult to locatewhen you are in a pinch. Ref BMW 135320

Mercedes Special Tool 00

Special Tool for MERCEDES Star.
Chrome plated,with T handle made of black plastic,for mounting and removing theMercedes Star at the engine hood
on class S (W 140), E(W 124 since model 93) and C (W 202)

Honda Toyota Nissan Tool 45.95

12mm Jam Nut Valve Adjustment Tool
Designed for a wide variety of cars with 12mm jam nut valve adjustment screws.
This two in one tool has a window in its socket so the technician can see the position of the screwdriver blade holding the
adjustment screw as the jam nut is tightened.
This visual contact in addition to the feel of holding the screwdriver The unique handle pivots from one side to the other, so the window is always visible.

Toyota Cam Installer Set 49.50

Installer Kit used for proper installation of cam shaft seal on transverse mounted Japanese engines,placing cam shaft within close proximity to shock tower.Due to this confined space, it is difficult to replace cam seal using conventional methods.Applicable: Toyota Engine 3AC, 3EE, 3S FE, 3S GE, 4AC, 4A GE, 5S FE, 7M GE, 7M GTE.Mazda B6, BP. Nissan engine VG30.

Set 3 Valve Tools 105.50
VALVE ADJUSTING TOOL SET OF 3
Valve adjusting on the Rabbit, Scirocco, and Jetta 1 requires the use of a special tool to hold the cam followers in the down position in order to remove the shims for replacement. The valve adjusting pliers are then used to remove the shim. Note: The 1.6 and 1.7 liter engines use a different tool than the 1.8 liter engine becuase of valve spacing. The Shim Set works on all solid lifter cylinder heads.
read more:

Set of Two Terminal Tools 29.50

Special Electrical Tools Terminal Tools Set of 2
Special Electrical Tool Terminal Tool Eliminate Damaged wires and Terminals. Wire Terminal tools are designed to remove wires from terminals without damage to either. The prongs depress the "barbs" on conventional terminals.

Radio Removal Tool Special 15.99

Very popular BMW Radio Removal Tool.Pentagon shaped tool with 5 Sides.The overall length of this tool is 3 5/8 inches.Applicable: Most BMWs.Including E38 E39 7 Series etc...This tool is used to release anti theft radio mounts.
Plus you get a 15 Piece Ratchet and Bit SetIncludes 6 each 1/4 drive 6 point sockets sizes 3/16, 1/4, 5/16 plus 6, 7, and 8mm.Also included are 6 screwdriver bits 2 slotted ( 3/16 and 1/4) 3 Phillips (1, 2 and 3) plus a 1/4 Dr Hex adapter.You can use the 6, 7 and 8mm hex sockets for hose clamps on German cars and many other applications.Set comes in a blow molded carrying case.

Knipex 4 in One Plier 34.99
Dont have this tool???
You need to git one!
Crimping and Stripping Pliers
Four functions in one tool!
Grip, strip, cut and crimp!
. Crimps cable links
. Strips 10/12/14 AWG wire
. Factory tested for copper / aluminum cable and hard wire
. Made of high strength special grade steel
. Plastic coated handles and polished head
. 6 1/4" overall length
read more:

Double Holder Tool 24.50

Double Waterpump Tool*
This special tool covers most popular applications
Used for securing Water Pump Hub from rotating during R & R of Fan Clutch Nut
BMW engines:M10, S14, M20, M21, M30, S38, M40, M41
M42, M43, M44, M50, M52, M60, M62, S50
Should be used in conjunction with a 32mm or a 36mm thin wrench.

Special Pliers 65.00

Special Pliers for outside Mirror switch
Original tool Made in Germany

Headbolt & Drain Plug Socket Set 28.00

TWO TOOLS!!!
Audi Headbolt Tool (LEFT)Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Plus Drain Plug Socket (right)Special Tamperproof Transmission Drain Plug Socket.Triple Square (12 Point XZN)Same as Volkswagen Tool 3357.For Porsche Boxster and Audi A4, A6 and Passat. Dont hesitate...these are BOTH the CORRECT tools for the job!

ZDMAK SPECIAL 2 Brake Tools 49.95

This sale is for two brake tools.
First tool on the UPPER LEFT is Drift Pin 4mm
Tool used for removing disc brake pads.
This Drift pin is designed to press the brake pad retaining pins back w/o damage to pin or caliper.
For a variety of brake applications. (overall length is 7 inches.)

Second tool LOWER RIGHT is the Spreader/Disc Brake Piston Reset Tool
This is a very useful tool for safe resetting of disc brake pistons on vehicles with fixed caliper disc brakes.

Audi Headbolt Tool 17.50

This is the tool you are looking for!
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Brake Caliper Rewind Set 47.99
U.S./EURO/ASIAN/4WD VEHICLES
Disc Brake Pad & Caliper Service Tool Kit
Includes 8 adapters Magnetic socket adapter.
For brake assemblies
For rotating pistons back into caliper to provide clearance for new pads
Prevents damage to the piston and bootDesigned for use with Mercedes, BMW, Volkswagen, GM, Audi, Ford,Honda, Subaru, Mazda, Nissan, Mitsubishi, Toyota, Land Rover and 4 wheel drive vehicles.Blow molded carryingcase for easy storage.
read more:

Holding Tool & 32mm Wrench 39.99

Set of two tools for BMW Repair Includes:
Double Waterpump Tool. This special tool covers most popular applications
Used for securing Water Pump Hub from rotating during R & R of Fan Clutch NutApplicable:M10, S14, M20, M21, M30, S38, M40, M41M42, M43, M44, M50, M52, M60, M62, S50

Plus Long Pattern "Thin Wrench" 32mm Open End.
What makes this set different from other sets you will see is the 32mm wrench. This is a heavy duty tool and 20 inches long.
No one else has a set like this for the price. The 32mm is a WHOPPER.

Holding Tool and 36mm Wrench 39.99

SET OF 2 Includes:
* Double Waterpump Tool*
This special tool covers most popular applications
Used for securing Water Pump Hub from rotating during R & R of Fan Clutch Nut
Applicable:M10, M20, M30, M40, M41, M42, M50, M60, M62

Plus
Long Pattern Thin Wrench

Size: 36mm Open End.

BMW Daily Double 27.50

Daily Double!
Two Tools
Including Item Number BMW3022: Radio Removal Tool.Pentagon shaped tool with 3 5/8 inches overall length.Applicable: Most BMWs.This Five sided driver is used to release anti theft radio mounts.
Plus the two sided counter holder. More details about this tool number BMW 1703 Waterpump Tool
This special tool covers most popular applicationsUsed for securing Water Pump Hub from rotating during R & R of Fan Clutch NutApplicable:M10, M20, M30, M40, M41, M42, M50, M52, M60, M62 (1703 should be used in conjunction with a 32mm or a 36mm thin wrench). Picture is not to scale.

Super Duty Headbolt Tool 37.50

Headbolt Tool ....Read:
Same as Number T10070
Super Strong Headbolt Tool 1/2 Drive
(notice the solid one piece design)
Tool used to remove and install cylinder headbolts. New "Stronger" One Piece design. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2" Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socket The old tool number was 3452 and is now discontinued.. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. The German Tool Books call this a Polydrive. This is NOT a Torx socket although it is a 6 point tool. The points are more flat (squared off) than a torx. and it is NOT a XZN (tri square) Socket.

Terminal Tool Wire Remover 13.99
Special Electrical Tools Terminal Tool Eliminate Damaged wires and Terminals.
Wire Terminal tools are designed to remove wires from terminals without damage to either. The prongs depress the "barbs" on conventional terminals. See set of 2 below.
read more:

Headbolt Socket 17.50

This is the tool you are looking for.
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Universal Cam Pulley Holder 55.00

Universal Cam Pulley Holder Comes in a plastic pouch with two sets of Pins. This tool isused on some Honda, Nissan, Mitsubishi, Toyota, Volvo Ford, Chrysler, Mercedes and BMW.

New Style Headbolt Polydrive 17.50

This is the tool you are looking for!
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen AudiV6 and 4 Cylinder5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Audi Headbolt Toolt 17.50

Oil Service Wrench 14x17 39.50
Oil Wrench 3677This is a special tool is designed for changing oil. The Male hex key is 14mm and the female ( box end ) is 17mm. Made in Germany by Stahlwille.
read more:

Thin Nose Type Special Wrench 19.99
Attention Harley People
(or anyone looking for a very unique tool)
This is a 'must have' tool for your tool pouch! It is only 8 1/4 inches long, light weight and strong. The jaws open large enough to handle any Harley axle nut, a full 1 1/2 inch. It is 1/4 inch thinner than a standard adjustable wrench This wrench has a thickness of 1/2 inch; allowing you to take the rear tire off your scoot without removing the mufflers on an FL touring model. It has a very comfortable rubber grip with a hole in the end of the handle so you can hang it on the wall or attach a lanyard. Best of all it adjusts tight on the nut and the jaws will not flex when you reef on it. There is a metric scale on one side and an SAE scale on the other just in case you want to know the size of the nut. Do not loan this wrench to a friend, you might not get it back!ClickHere to see the tool in action!
read more:

Ferrari Head Bolt Tool 00

Special 8 Point
Offset ring Wrench for Headbolts.
Available 15mm or 17mm both come 1/2 inch drive.
The overall length of the tool will be 274mm.

Brake Piston Tool 14.99

Disc Brake Piston Cube Tool has 5 different drive pin configurations designed to rotate the parking brake activated piston back into the caliper cylinder when replacing worn pads on vehicles equipped with 4 wheel disc brakes. Tool will service many domestic and import cars. This tool will work in place of special tool 3272. Some Audi VW calipers (mid 80s) use a hex tool check yours to be certain a pain in the neck if you have never done them before. Grind or file off two diagonally opposite corner pins to allow the cube to fit the vw rear brake piston. Use with a 3/8" ratchet. It can be easier to fasten the rear caliper back onto the carrier without the rotor in place while using this tool. That way you get a little extra leverage. Use as follows: engage the two prongs and turn the piston 180 clockwise. Remove the tool. Use a generic calper tool or a c clamp and push the piston in about 2mm. Keep alternating back and forth between the cube tool and the c clamp until the piston in almost all the way in. If you are strong enough, you may not even need the c clamp just push with the cube tool as you turn. Instead of the cube, you can even use needle nose pliers, but then you defintiely need the c clamp. The rear brakes can be rather difficult, so make sure you have plenty of time. Also for use on most popular imports and Chrysler, Ford and GM vehicles with 4 wheel disc brakes.

Special Hook 3370 30.00

Factory Tool 3370
Made in Germany.
TOOL USED TO REMOVE FRONT SEAT BACK REST PANEL ON AUDI A4.

Triple Square Drain Plug Tool 49.50

This is a Special Tamperproof * Transmission Drain Plug Socket. Triple Square ( 12 Point XZN 16) Same as old Volkswagen Tool 3357. (Number 3357 is still found in many/most manuals for this job)
Applicable Porsche Boxster and Audi A4 A6 and Passat. This is an excellent high quality tool Made in Germany. Plug not included, picture is for reference only.

LED Tester 53.99

NUMBER VAG1527BLED Tester Factory Tool VAG1527B Special Tool for diagnostic troubleshooting.3 to 48V range.

Hazet Tensioning Tool 75.98

Driving Tool for Tensioning Device
special steel, for operating devicewhen changing the V ribbed belt,especially on VW Polo, Golf and Passat, AUDI since 1991.

Oil Service Wrench 14 x 17 52.50

Oil Wrench 14 x 17
Special tool designed for oil service.
The Male hex key is 14mm and the female ( box end ) is 17mm.
High Quality Tool
Made in Germany.

You Searched for

toyota special tool

Trade Links With ZDMAK