mercedes timing tool SARASOTA mercedes timing tool xzn socket tool -- mmk4mkt

Dial Indicator Holder 37.50

Indicator Holder
This is the tool you need if you have been searching for a holder that will accomodate your indicator ONLY IF YOUR INDICATOR HAS A SHANK SIZE OF 3/8
MOST OF THE OTHER HOLDERS ON THE MARKET ARE FOR 8MM SHANK.
THIS IS FOR 3/8
IF YOU SEE A COPY OR A CHEAP IMITATION OF THIS ITEM WITH THESE DIMENSIONS YOU CAN BE SURE IT IS NOT A QUALITY TOOL!
This is a Quality Holder you will not find a tool (with these dimensions) at a better price anywhere!
Used for the accurate setting of the Bosch diesel fuel injection pump timing.
The Holder screws into the back of the injection pump,
giving a dial indicator reading necessary for setting
the correct pump timing.
This tool will help you complete your set having the correct tools for the job is important to any serious mechanic!
Included with the Holder is the 10cm Dial Indicator Extension Pin,
making the timing easy to set,
as the timing has a range from 0.83mm to 1.15mm.

Cam Spoke Lock Device 85.00
Twin and Quad Cam Spoke Lock Device
Universal Twin Cam Number 2727Used for securing Twin Cam Pulleys.
Applicable: All twin or quad cam engines with timing belt pulley sprocket on each cam.Used for the crucial task of securing twin cam pulleys from rotating during the R&R of timing belt. Fully adjustable, this tool comes complete with 1 pair 8" and 1 pair 4.5" long, Left/Right hand threaded rods.The shorter needed for confined spaces where the rods might interferewith the fire wall or other auto part. Fully constricted onto the spokesof the cam pulleys and locking down the securing wing nuts,reveals a 6 point locking mechanism.This tool will remain rigid, not allowing for any movement of cams, saving your timing.Please note:With Quad cam pulley engines 2 sets of tool 2727 are needed to complete the task.All Twin or Quad cam equipped with a timing belt pulley sprocket on each cam.
read more:

Cam Bar for 5 Valve 129.50

Camshaft Timing Tool Securing Bar
TOOL REF 3391
Cam Securing Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 (2002 4 cam)
Please note: 3391 for 5 valves per cylinder.

Mercedes 8mm Dogleg Allen 14.95

Sturdy 1/2 Drive Dog leg (offset) 8mm Allen SocketApplicable: M116, 117
1/2" drive
Overall length of the tool is 4 1/4 inches.
Tool used for R&R of cylinder head bolts.
Similar to Mercedes number 000 589 3407 00.

Mercedes Special Tool 00

Special Tool for MERCEDES Star.
Chrome plated,with T handle made of black plastic,for mounting and removing theMercedes Star at the engine hood
on class S (W 140), E(W 124 since model 93) and C (W 202)

Benz Transmission Tool 49.95

Transmission Linkage Bushing Installer / Tool for Mercedes Benz with automatic transmissions, virtually all later models, some Ford and other vehicles needing this tool to easily and safely push TOUGH nylon bushings into place. Works on different bushing sizes. The design of this tool was initiated by Mr. Robert Allen and has recently been modified and perfected. Robert Allen is a long time Mercedes Benz Master Technician with 26 years of experience.

Bar and Pin for 5 Valve 139.50

Camshaft Timing Tool Set (2)
TOOL REF 3391
Cam/Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 2002 4 cam.

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6Please note: 3391 for 5 valves per cylinder.

36mm Oil Filter Wrench 39.99

BMWMINI COOPER TOOL Mercedes Benzdiesel oil filter wrench.
This is the same as Mercedes item 606 589 01 09 00. Works on BMW and Mercedes
This tool is 6 point size 36mm shallow socket 3/8" drive.
Heavy duty construction. It is made by Hazet for Mercedes and BMW.
Good for engine OM606 used in 1995 W124 E300 diesel, 96 97 W210 E300 diesel,
and 1998 E300 turbodiesel. Also for MB Diesel Engines OM604, OM605
and BMW Mini, BMW M52 6 Cyl., M60 8 cyl., M70 12 cyl and Volkswagen VR6.
Some other applications include:
Mercedes diesel engines: OM604, OM605, OM606 1995 W124 E300 diesel,
1996 97 W210 E300 diesel, 1998 E300 turbo diesel.
BMW Mini Cooper, BMW M52 6 cyl, BMW M60 8 cyl, BMW M70 12 cyl.
VW Volkswagen VR6
Ford Truck 6.0L 2003 thru 2004
High Quality Hazet Tool Made in Germany!

36mm Oil Filter Socket Wrench 39.99

Cam Spoke Lock Device 79.00

Twin and Quad Cam Spoke Lock Device
Universal Twin Cam Number 2727Used for securing Twin Cam Pulleys.
Applicable: All twin or quad cam engines with timing belt pulley sprocket on each cam.Used for the crucial task of securing twin cam pulleys from rotating during the R&R of timing belt. Fully adjustable, this tool comes complete with 1 pair 8" and 1 pair 4.5" long, Left/Right hand threaded rods.The shorter needed for confined spaces where the rods might interferewith the fire wall or other auto part. Fully constricted onto the spokesof the cam pulleys and locking down the securing wing nuts,reveals a 6 point locking mechanism.This tool will remain rigid, not allowing for any movement of cams, saving your timing.Please note:With Quad cam pulley engines 2 sets of tool 2727 are needed to complete the task.All Twin or Quad cam equipped with a timing belt pulley sprocket on each cam.

Spring Compressor Kit 269.00

Special Low Price
Mercedes Coil Spring Compressor Kit
For front and rear coil springs.
Applicable: Mercedes chassis W107, W116, W123, W124, W126, W129, W140, W201, W202.
Comes with a convenient carrying case.
Ref: 924 589 0231 00
Call if you have any questions about this tool or any other tool.

Dogleg and 8mm Hex Set 29.50

Hex Tools (2) Dogleg Plus Regular 8mm Allen
Set of Two Tools Sturdy 1/2 Drive Dogleg (offset) 8mm Allen SocketApplicable: M116, 117
Overall length of the tool is 4 1/4 inches.
Tool used for R&R of cylinder head bolts.
Similar to Mercedes number 000 589 3407 00.
Plus 8mm (straight) standard Hex 1/2 drive.
Excellent tools for working on Mercedes and other German vehicles.

Mercedes and BMW Set 89.50

ON SALE 7 Pc Benz and BMW Tools Including 4 Mercedes Tools a BMW Holding Tool plus 2 Thin Wrenches.
Benz Tools are:
1.Hub Securing Bar 113 0040 Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable:M112 & M113

2.Locking Hook needed for securing the visco fan couplingduring R&R of 8mm hex fastener w/o removing the radiator: Mercedes M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Comes complete with 8 and 10mm Allen bits.The 8mm is needed for R&R of fan clutch fastenerApplicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606The 10mm is used for adjusting A/C belt tension and R&R of idler pulleyModels 420, 560 with V 819 86 and Newer
4. Thin Wrench 65mm with an 8mm overall thickness and an overall length of 16 inches for proper leverage. Mercedes ref: 120 589 0201 00

BMW Double Waterpump ToolThis special tool covers most popular applications used for securing Water Pump Hub from rotating during R & R of Fan Clutch NutApplicable:M10, M20, M30, M40, M41, M42, M50, M60, M62

Fuel Tool Mercedes Benz 39.50

Cup Wrench for Mercedes W202. Used to remove fuel sender retainer.

3 Mercedes Tools 151.00

Set of Three including: Threaded Pin Wrench Socket (M0007) tool used for the proper R&R of threaded ring which secures prechamber in cylinder head. The Mercedes number for this tool is 615 589 0007 00
Applicable: OM601/602/603 engines through 1989 with vertical injection. Also OM615, OM616, OM617 Ref: 615 589 0007 00
Plus
Extractor Tip Double Ended (M0046) Used for the proper removal of prechamber from cylinder head. Used in conjunction with a slide hammer.
Applicable: Mercedes engine OM601, OM602, OM603, OM604, OM615, OM616, OM617. Ref: 902 589 0033 00
Plus
Slide Hammer use with Tool M0046 for proper removal of prechamber from cylinder head. Also other applications: Tool pulls dented sheet metal back into place. To use, drill a hole in the deepest part of the dent, insert the hook or self threading screw tip and tap lightly with the 2 1/2 lb slide hammer to remove the dent.
A 13' long shaft enables high pulling force. Slide hammer has 1/2 13 UNC thread.

T30 Airbag Torx Bit 8.50
Long Torx Bit T30
Airbag Tool Torx (6 Point) Overall Length is 4 inches. Super High Quality Tool for BMW, Mercedes and VW.
read more:

Mercedes Socket 45.50
Mercedes Diesel Injection Pump Socket
M0019Mercedes 32 Point Female Socket with 1/2" drive, This socket is used for the R&R of delivery valve of diesel injection pump.Applicable: Mercedes diesel engines.
Ref: 617 589 0109 00
read more:

V8 Camshaft Securing Bar 135.00

V8 Timing Tool T40005
Camshaft Securing Bar Audi A6 / A8
Used for the crucial taskof securing both engine banks, cam shafts at T.D.Cwhen replacing the timing belt.

Red X Dog for Mercedes 220.00

This Mercedes reset tool can do more than other reset tools!
First, it provides you with the capability of resetting the service reminder displays.
In addition, you can also reset airbag faults and turn off the airbag (SRS) indicator. Applicable: 163 ML Class, Light Truck

Mercedes Locking Nut 39.95
Locking Nut M0039needed for securing the diesel injection pump cam shaft.Applicable:Mercedes OM601, OM602, OM603, OM605, OM606, OM617.Benz Ref: 601 589 0521 00
read more:

Door Handlle Hinge Kit 79.50
Tool Kit for BENZ , VW , AUDI , PORSCHE door hinge/handle installer & remover.
Finally, a compact solution to accessing the special features found on the door hinges and door handles of VW/Audi, Mercedes Benz and Porsche, includes 4 door hinge bits (less than 1 inch long) with slender ratcheting wrench and extra long drivers for accessing Mercedes and VW door handle fasteners.
read more:

2 Pins and 2 Plates 103.00

2 Pins and 2 Plates Set of four tools.VW Audi T.D.I. and New Beetle Cam Kit Reference numbers for the two tools on the left are: 3418 and 3359. Tool Set for factory correct and trouble free installations. This is a popular set for Diesel timing of Bosch injection pumps. This set has been developed for aligning the cam shaft with the Diesel pump on 1998 and newer VW models equipped with a T.D.I. engine. This two piece lock plate and alignment pin allows the technician for factory correct and trouble free installations.

Tools on the right side of image are Diesel Lock Plate / Cam Setting Bar Same as Volkswagen ref 2065a Tool used for securing the cam shaft from rotating and maintaining correct timing position engine AAZ during R&R of cam shaft drive belt. Applicable: VW/Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 Lock Pin for Diesel (Same as VW tool 2064). Tool used for securing Bosch diesel injection pump sprocket from rotating during R&R of cam shaft drive belt. This Locking Pin also assists in locating the general timing position of pump. Volkswagen Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 All 4 tools are High Quality Made in Europe!

Long Torx Bit T30 Airbag Tool 6.99

Long Torx Bit T30
Airbag Tool Torx (6 Point) Size T30
Overall Length is 4 inches. Quality Tool for BMW, Mercedes and VW.
High grade tool steel bits,
hardened for ultimate wear resistance.

Audi Info and Timing 0.00

There are three main Cam bars for timing.
3391, 3243 and T40005
(T40005 is for V 8)
Notice the tool number 3242 this is the T.D.C (TOP DEAD CENTER) Pin
This pin goes with 3391 or 3243.
Type your selection in the search or you can find the tools in this Audi section.
Feel free to call me or email. I will try to assist you.
Please note:
In order to make your selection you must determine if your vehicle is 2 valve per cylinder or 5 valve per cylinder or V8. Example = Notice tool number 3391 says it is for 5 valve. The 3243 is for 2 valve per cylinder.

Engine Turning Bar Double Row Timing Chains 55.50

Engine Turning Bar used for adjusting valves and timing.Applicable: BMW with dual timing chains.

Timing & Cam Tools 0.00

Please note: There are three main Cam bars for timing.
Choose from 3391
3243
and T40005 (the T40005 is for V 8)
Notice the tool number 3242, this is the T.D.C TOP DEAD CENTER Pin. This pin goes with 3391 or 3243. Type your selection in the search or you can find the tools in this section. You should refer to a manual if one is available to you, or feel free to call me or email. I will try to assist you. Please note:
In order to make your selection you must determine if your vehicle is 2 valve per cylinder or 5 valve per cylinder or V8. Example = Notice tool number 3391 says it is for 5 valve. The 3243 is for 2 valve per cylinder.

T30 Airbag Tool Torx Bit 8.50

Long Torx Bit T30
Airbag Tool Torx (6 Point) Overall Length is 4 inches. Super High Quality Tool for BMW, Mercedes and VW.

Double & Single Row Set up Complete 270.00

Master Link Timing Chain Tool
Single Row and Double Row Set up.
Used for proper assembly of timing chain master link.
OM601, OM602, OM603, OM615, OM616, OM617
(also M102, M103 AND M116)
You will get all (3) bits for double and single row.
Picture above is for reference only.

Engine Turning Bar Single Row Timing Chain 92.50

Engine Turning Bar used for adjusting valves and timing.Applicable: BMW and 6 cyl engines with a single timing chain

Cam Bar for 2 Valve 129.50

Camshaft Securing Bar Timing Tool
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4 94 97 AFC Engine
Please note: 3243 Securing Bar for2 valves per cylinder.

Best Seller ! Radio Tools Set 24.99

This is one of the best sets on the market. This is a Master Set for BMW Mercedes Porsche VW Audi and DIN. Included is a total of 3 different sets Volkswagen Audi, two different tools for BMWand a set for Mercedes Porsche and a DIN Ford set. The VW Tools (4) Number T10057Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box. If you have 4 slots VW AUDI this is the 4 keys you need) Plus you get Number VW 3316 (2) Radio Removal Tools New Body Style Passat Jetta Golf . You will get virtually full coverage forVolkswagen Audi when you buy this master set. The BMW Radio Removal Tools areone Pentagon shaped tool with a 3 5/8 inches overall length. Applicable: Most BMWs. This Five sided driver is used to release anti theft radio mounts.You will also get the special rare small allen tool for BMW (upper left) Fornewer BMW E38 & E39 7 SERIES Plus Mercedes most coverage for newer and oldervehicles, especially 1992 and newer 129, 140, 163, 202 & 210 PLUS Range Rover with Becker Nav System.The MB Tools also work on Porsche. Appl: Turbo GT, GT2, GT3, Boxster, Cayenne 911, 996 , 987, Carrera etc. Same as Porsche ref: 000 721 957 01

Spanish Timing Manual 49.00
Description:
2002 Spanish Version
Timing Belt Manual
read more:

Grand Master! Radio Tool Set 34.99

Master Radio Removal Tool Set
18 Piece Set includes the following tools needed to install and remove radios :. 2pc. Radio Removal U Hook (Ford/VW/Audi/Grundig/Blaupunkt) . 1pc. Special Pentagon Wrench (BMW). 4pc. Radio Removal Keys (VW/Audi/Becker/Mercedes Benz) . 2pc. Radio Removal Keys (Mercedes Benz/Porsche/Becker). 2pc. Radio Removal Keys (VW). 1pc. Allen Hex Wrench (BMW/Opel). 2pc. Radio Removal Keys (New Becker). 2pc. Radio Removal Keys (New Skoda). 2pc. Radio Removal U Hook (New Blaupunkt)

Timing Tools (2) 88.50

New Beetle and T.D.I. Cam Kit Tool Set for factory correct and trouble free installations. This is a popular set for Diesel timing of Bosch injection pumps.This set has been developed for aligning the cam shaft with the Diesel pumpon 1998 and newer VW models equipped with a T.D.I. engine.This two piece lock plate and alignment pin allows the technician for factory correctand trouble free installations Reference: 3418 and 3359.

Chain Sprocket Tool 31.00

P204 Chain Sprocket Tool Used for securing the chain sprocket and preventing chain slippagethis tool is important when replacing tensioners or setting cam timing. 911 930.

Locking Pin and Plate 26.00
Set of two tools including:2065A Diesel Cam Shaft Locking PlateThis locking Plate (above) is the same as vw tool 2065a Used for securing the cam shaft from rotatingand maintaining correct timing position during R&R of cam shaft drive belt.Applicable:All VW/Audi Diesel and Volvo 6 cylinder 2.4L diesel '81 '86 engines. PLUS:2064 Lock Pin for Diesel This Locking Pin is used forsecuring Bosch diesel injection pump sprocket from rotatingduring R&R of cam shaft drive belt.This Pin also assists in locating the general timing position of pump.Applicable: All VW/Audi diesel engines.
read more:

LightOff for Mercedes 229.00

Individual Oil Service/Inspection light, SRS (Airbag) reset tool.This unit provides you with the capability of resetting the oil service reminder, in miles and days for the next service.
In addition, you can also reset SRS (airbag) faults (and its dashboard indicator)
on all Mercedes with diagnostic capabilities, and the 38 pin diagnostic connector (excluding the M Class Light Truck, Model 163).
Applicable: Chassis 124, 129, 140, 163, 170, 202, 208, 210, 463, vito, Sprinter

Set 3 BMW Tools 125.00

Set 3Repair Tools for BMW
Alignment Jig Number 113240
Pin Number Number 112300
Tensioner Number 113390

Used for setting cam shaft timing.
Kit includes (2) blocks (1) swivel lock and (1) locator pin.
Applicable: BMW engine M42, M44, M50, M52, M52TU.
The ref number for the Jig ( 2 blocks) 113240
and the Pin is 112300RigidChain Tensioner 113390 Ref: BMW Tool 90 88 6 113 390
Tool is used for tensioning primary chain when adjusting valve timing.
Late model V8 Applicable: M50, M60, M62

Winner gets all tools pictured.

Hazet Oil Service Tool 29.50

Oil service Wrench 74mm with 14 Points (inside flats flutes).
Some applications include: Mercedes, Audi, VW Golf,
and new body Jetta, TDI (Diesel) and the following gas vehicles;
Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco,and New Beetle.
Mercedes M104, M110, M111, M119, M120 C, E
Porsche 944 and 924. 
Some Toyota (Filter 08922 0211 etc...)
Can also be used on BMW Top of housing 1.9L M44
Super High Quality Original Factory Tool Made in Germany!
Clickhere to see a detailed Application ChartMeasure filter diameter canister diameter or Check yourmanuals for details and size needed.

Pin Wrench T.D.I. 26.99
Pin Wrench Angle Type
NUMBER T10020 VW AUDI TENSION PULLEY SPANNER WRENCH
This unique tool is for 1998 and later VW and Audiwhich require spanner wrench adjustments to the timing belt.
read more:

Tensioner Tool 12.99

P214 Used for securing tensioners in their retracted position during installation.This tool helps keep the chain timing correct during this procedure.911 with factory tensioners (Excluding pressure fed types)

114230 Rigid Chain Tensioner 29.50

Rigid Chain TensionerBMW114230Ref: BMW Tool 90 88 6 114 230
Tool is used for tensioning primary chain when adjusting valve timing.
Late model V8 Applicable: M50, M60, M62.

Dial Indicator and Holder 98.50

Bosch Diesel Injection Pump
Timing Indicator Tools.
With High Quality Dial Indicator Made in Germany!
You will not find this price anywhere except Zdmak!
Tools are used for the accurate setting of
the Bosch diesel fuel injection pump timing.
The Holder screws into the back of the injection pump,
giving a dial indicator reading necessary for setting
the correct pump timing.
This set comes complete with the correct tools for the job!
Contents: Metric Dial Indicator Made in Germany,
plus holder plus the 10cm dial indicator extension pin,
making the timing easy to set,
as the timing has a range from 0.83mm to 1.15mm.
For use on VW and Audi diesels.
Also works with 1981 1986 Volvo 6 cyl 2.4L diesels,
1989 1994 Dodge 6 cyl 5.9L diesels.

FYI FOR PEOPLE WHO DECIDE "NOT" TO USE THIS SET
Here is some helpful info...Universal conversion factor for milimeters into decimal inches is .03937
EXAMPLE: 13mm X .03937= .5118"

BMW Repair Tool 125.00

116180 FixtureAppl:M52, M52TU, M54 Details:Place chain wheels in special tool 116 180, position tooth gap in inlet chain wheel and feed on chain. For timing of the double Vanos cam adjustment for 1998 and later 6 cylinder BMW. Use it together with tools BMW113 240, BMW113290, BMW112300, BMW114220, BMW116150

Timing Kit Master Set 1 254.00

Serious Master Set: Description (for upper 3 tools) Timing belt on engine ALH. Chassis 1999 1/2 thru 2003 Golf Jetta (A4) MKIV and New Beetle TDI thru 2003.Reference numbers for the three tools are 3418 (Left side of image above) 3359 (Pin Center) and T10020 (Wrench Right. This is a popular set for Diesel timing of Bosch injection pumps. This set has been developed for aligning the cam shaft with the Diesel pumpon 1998 and newer VW models equipped with a T.D.I. engine.

BELOW IS THE DESCRIPTION ON THE LOWER 5 TOOLS. Five tools: vw 3032, 2066, 2065A, 2064 and 12717 (Pin Wrench) Details: 3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: VW / Audi diesels : 2066 Used for accurate adjustment of Bosch diesel injection pump. 2065A Diesel Camshaft Locking Plate Tool 2064 Lock Pin for Diesel. Pin Wrench 121717 Made in Germany for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of idler pulley and rotates around the off center retaining bolt allowing for belt tension adjustment (Tension Pulleys) 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80. You will get all 8 tools shown here.

Locking Pin and Plate 26.50

Set of two tools including:2065A Diesel Cam Shaft Locking PlateThis locking Plate (above) is the same as vw tool 2065a Used for securing the cam shaft from rotatingand maintaining correct timing position during R&R of cam shaft drive belt.Applicable:All VW/Audi Diesel and Volvo 6 cylinder 2.4L diesel '81 '86 engines. PLUS:2064 Lock Pin for Diesel This Locking Pin is used forsecuring Bosch diesel injection pump sprocket from rotatingduring R&R of cam shaft drive belt.This Pin also assists in locating the general timing position of pump.Applicable: All VW/Audi diesel engines.

36mm Oil Filter Wrench 15.99

Special 36mm Oil Filter Wrench Removes and installs filters on BMW Mini Cooper. The low profile socket fits 36mm fuel and oil filters. The low profile socket works in confined spaces. 3/8 in. drive Not for use with an impact wrench.
BMW Mini Cooper, BMW M52 6 cylinder, BMW M60 8 cylinder, BMW M70 12 cylinder.
Mercedes Benz diesel engines: OM604, OM605, OM606 (1995 W124 E300 diesel, 96 97 W210 E300 diesel, 1998 E300 turbodiesel).
Same as Mercedes tool number: 606 589 01 09 00VW Volkswagen VR6
Also for Ford Truck 6.0L 03 04

MULTI SERVICE INTERVAL RESET TOOL 389.00

MULTI SERVICE INTERVAL RESET TOOL Number OR300 Reset tool is necessary for workshops to maintainand reset Mercedes Benz, BMW, Volvo, VW/Audi vehicles.With the large LCD display and the individual professional connectors, anyone can operate this tool clearly and easily just follow the instructions on the display.Convenient professional package comprises of the base unit, individual diagnostic connectorsand instruction manual in a small carrying case.
Readabout it Here

Chain Tensioner and Bracket 74.50

Set of 2 Tools
Rigid Chain TensionerBMW114230 plus 112400 Bracket.
Tensioner is Ref: BMW Tool 90 88 6 114 230
Tool is used for tensioning primary chain when adjusting valve timing.
Late model V8 Applicable: M50, M60,M62.
Bracket is number 112400 used for screwing in tensioner with case cover removed.

Belt Tension Guage 54.50

Belt Tension Guage Special Tool used to adjust the tension on the cam belt where the movement of timing belt is measured by load (NM). Suitable for use on cam belts various belt widths. Easy to use. Clear incremental marking with knurled knob for precise measurement. Dual scale allows reading from top or bottom of tool.

You Searched for

mercedes timing tool

Trade Links With ZDMAK