Thin Head Flexible Ratchet 79.99
Ever see this one? It is a Super Tool....
A flexible "Thin Head" Reversible bit holding Ratchet.
(the reverse mechanism is on the flip side of photo not shown)
The head will flex backwards forwards more than a 90 degree (70 to 80)
The thickness of the head is 10mm
The overall length is 164mm ( 6 1/2 inch).
This tool is great for getting into a tight spot with a special bit,
during rare or difficult procedures (bits not included)
Call if you are looking for a special bit to go with the tool.
read more:

GrabBit Screw Remover 19.99
No other screw extractor removes damaged heads AND extracts free spinning screws!
GrabBit Damaged Screw Remover
and Bolt Extractor Kit
Can be used for removal of most screw head types and drive styles 2 sizes are capable for removing screw size number 6 up to 3/8' diameter bolts Works on all materials including hardened grade 8 steel and stainless steel.
Insert GRABIT directly into drill or quick change chuck Burnishing end is showing Set drill for reverse (counterclockwise). Place Burnishing end of tool into damaged screw, slowly clean inside screw head until smooth. Note: Burnishing tool end in not to be used to drill a hole. RemovingRemove Burnishing end from chuck, flip tool, replace into drill chuck Remover end now showing. Maintain reverse setting (counterclockwise). Place Remover end of tool into now smooth screw head. Apply firm downward pressure, drill at slow speed. Apply lowest level of power to the hand drill. Remover end of GRABIT will thread into screw head and remove.

ReusableThe GRABIT Damaged Screw Remover is reusable. Clean chips off toll and lubricate with oil after use.
WarningAlways wear safety glasses when operating or near power tools.
Cutting tools may shatter when broken.
read more:

Metric Nut & Bolt Gage 4.99
Metric (and inch) Nut & Bolt Gage
For fine thread and coarse thread nuts.
A very handy pocket tool for the European auto mechanic.
read more:

Locking Extension 10 In. 16.50
Hand Drive Locking Extensions NewThis Tool is 10 inches long and 3/8 drive. The image does not show but the "handle end has a square drive hole to use with a ratchet or T handle etc....Sockets Lock onto EXTENSION Pull sleave to release. Start fasteners by hand and finish with ratchet, or T handle or power tool. If you are a track or autocross junkie or if you've ever changed a wheel on a European car with hubcentrics and lug bolts, the hand drive locking extensions are a must for your toolbox! In fact, if you've ever tried to hand thread a bolt with one hand manually, or by using a socket with or without an extension, this product is for you. Simply attach your socket to the hand drive locking extension, put your bolt in the socket, and use the screwdriver grip on the extension to start threading the bolt! Then attach your ratchet, impact wrench or torque wrench into the 3/8 drive socket in the end of the screwdriver grip, and finish the job! This tool virtually eliminates the frustrating and sometimes costly crossthreading that starting a bolt with a power driver or impact wrench can cause. I'm replacing my other socket extensions in my toolbox with the hand drive locking extensions
read more:

Locking Extension 6 In. 16.50
Hand Drive Locking Extensions NewThis Tool is 6 inches long and 1/2 drive. The image does not show but the "handle end has a square drive hole to use with a ratchet or T handle etc....Sockets Lock onto EXTENSION Pull sleave to release. Start fasteners by hand and finish with ratchet, or T handle or power tool. If you are a track or autocross junkie or if you've ever changed a wheel on a European car with hubcentrics and lug bolts, the hand drive locking extensions are a must for your toolbox! In fact, if you've ever tried to hand thread a bolt with one hand manually, or by using a socket with or without an extension, this product is for you. Simply attach your socket to the hand drive locking extension, put your bolt in the socket, and use the screwdriver grip on the extension to start threading the bolt! Then attach your ratchet, impact wrench or torque wrench into the 1/2' drive socket in the end of the screwdriver grip, and finish the job! This tool virtually eliminates the frustrating and sometimes costly crossthreading that starting a bolt with a power driver or impact wrench can cause. I'm replacing my other socket extensions in my toolbox with the hand drive locking extensions.
read more:

Locking Extension 6 In. 14.50
Hand Drive Locking Extensions NewThis Tool is 6 inches long and 3/8 drive. The image does not show but the "handle end has a square drive hole to use with a ratchet or T handle etc....Sockets Lock onto EXTENSION Pull sleave to release. Start fasteners by hand and finish with ratchet, or T handle or power tool. If you are a track or autocross junkie or if you've ever changed a wheel on a European car with hubcentrics and lug bolts, the hand drive locking extensions are a must for your toolbox! In fact, if you've ever tried to hand thread a bolt with one hand manually, or by using a socket with or without an extension, this product is for you. Simply attach your socket to the hand drive locking extension, put your bolt in the socket, and use the screwdriver grip on the extension to start threading the bolt! Then attach your ratchet, impact wrench or torque wrench into the 3/8 drive socket in the end of the screwdriver grip, and finish the job! This tool virtually eliminates the frustrating and sometimes costly crossthreading that starting a bolt with a power driver or impact wrench can cause. I'm replacing my other socket extensions in my toolbox with the hand drive locking extensions.
read more:

Locking Extension 10 In. 17.75
Hand Drive Locking Extensions NewThis Tool is 10 inches long and 1/2 drive. The image does not show but the "handle end has a square drive hole to use with a ratchet or T handle etc....Sockets Lock onto EXTENSION Pull sleave to release. Start fasteners by hand and finish with ratchet, or T handle or power tool. If you are a track or autocross junkie or if you've ever changed a wheel on a European car with hubcentrics and lug bolts, the hand drive locking extensions are a must for your toolbox! In fact, if you've ever tried to hand thread a bolt with one hand manually, or by using a socket with or without an extension, this product is for you. Simply attach your socket to the hand drive locking extension, put your bolt in the socket, and use the screwdriver grip on the extension to start threading the bolt! Then attach your ratchet, impact wrench or torque wrench into the 1/2' drive socket in the end of the screwdriver grip, and finish the job! This tool virtually eliminates the frustrating and sometimes costly crossthreading that starting a bolt with a power driver or impact wrench can cause. I'm replacing my other socket extensions in my toolbox with the hand drive locking extensions.
read more:

Ball Tip * Torx Keys 00
Item97BTXDescriptionBall head offset key wrenches for Torx head screws, burnishedSpecificationsIts ball head shape allows the tool to be used with a slant of up to 30 from screw axial.Use short side for tightening where possible.
read more:

New * Locking Extensions 55.00
New Hand Drive Locking Extensions
Set of 4 including 1/2 drive(2) and 3/8 drive(2).
The image does not show but the "handle" end has a square drive hole to use with a ratchet or T handle etc....Sockets Lock onto EXTENSION Pull sleave to release. Start fasteners by hand and finish with ratchet, or T handle or power tool.If you are a track or autocross junkie or if you've ever changed a wheel on a European car with hubcentrics and lug bolts, the hand drive locking extensions are a must for your toolbox! In fact, if you've ever tried to hand thread a bolt with one hand manually, or by using a socket with or without an extension, this product is for you. Simply attach your socket to the hand drive locking extension, put your bolt in the socket, and use the screwdriver grip on the extension to start threading the bolt! Then attach your ratchet, impact wrench or torque wrench into the 1/2' drive socket in the end of the screwdriver grip, and finish the job! This tool virtually eliminates the frustrating and sometimes costly crossthreading that starting a bolt with a power driver or impact wrench can cause. You get a 6 and ten inch in BOTH drive sizes. Very cool set.
read more:

Cylinder Head Tool Kit 23.50
Cylinder Head Alignment Kit Same as Volkswagen Tool 3070
Set comes with (2) pairs of guide pins, 11X1.75mm and 12X1.75mm.VW model Scirocco, Rabbit, Dasher, Fox. Audi model 4000, 5000
read more:

New * Locking Extensions 33.50
Hand Drive Locking Extensions New
Includes one of each 6 and 10 inch long (extensions). 1/2 Drive. The image does not show but the "handle" endhas a square drive hole to use with a ratchet or T handle etc....Sockets Lock onto EXTENSION Pull sleave to release. Start fasteners by hand and finish with ratchet, or T handle or power tool.If you are a track or autocross junkie or if you've ever changed a wheel on a European car with hubcentrics and lug bolts, the hand drive locking extensions are a must for your toolbox! In fact, if you've ever tried to hand thread a bolt with one hand manually, or by using a socket with or without an extension, this product is for you. Simply attach your socket to the hand drive locking extension, put your bolt in the socket, and use the screwdriver grip on the extension to start threading the bolt! Then attach your ratchet, impact wrench or torque wrench into the 1/2' drive socket in the end of the screwdriver grip, and finish the job! This tool virtually eliminates the frustrating and sometimes costly crossthreading that starting a bolt with a power driver or impact wrench can cause. I'm replacing my other socket extensions in my toolbox with the hand drive locking extensions.
read more:

New * Locking Extensions 28.50
Hand Drive Locking Extensions New
This set is 3/8 drive and Includes one of each 6 and 10 inch long (extensions).The image does not show but the "handle endhas a square drive hole to use with a ratchet or T handle etc....Sockets Lock onto EXTENSION Pull sleave to release. Start fasteners by hand and finish with ratchet, or T handle or power tool.If you are a track or autocross junkie or if you've ever changed a wheel on a European car with hubcentrics and lug bolts, the hand drive locking extensions are a must for your toolbox! In fact, if you've ever tried to hand thread a bolt with one hand manually, or by using a socket with or without an extension, this product is for you. Simply attach your socket to the hand drive locking extension, put your bolt in the socket, and use the screwdriver grip on the extension to start threading the bolt! Then attach your ratchet, impact wrench or torque wrench into the 3/8 drive socket in the end of the screwdriver grip, and finish the job! This tool virtually eliminates the frustrating and sometimes costly crossthreading that starting a bolt with a power driver or impact wrench can cause. I'm replacing my other socket extensions in my toolbox with the hand drive locking extensions.
read more:

Special Rivet Tool 0.00
Special Rivet Tool
Plier with 90 degree rotating head.
Tool used to remove two piece reusable plastic rivets
found on door panels, engine shields, wheel well shields etc.
For undivided rivets the Plier can also be used for cutting the head off the rivet.
Easy to use universal Plier eliminates damage to trim and door facings.
read more:

Harley Bolt Wrench 46.95
Ratcheting Bolt Wrench for Harley Davidson Rocker Box Covers
For installation and removal of all Harley Davidson Evolution motor rocker box covers.. Reversible ratcheting action If using a conventional wrench, installers may unscrew the bolt up to the frame. Without the ability to reverse with a ratcheting wrench, the bolt will be lodged in that position. Low profile design gets into the tight spaces between engine and frame. 9 3/4' long handle for increased reach . Comfortable rubber grip will not scratch chrome. 3/16' Allen bit is replaceable. Made in the U.S.A.
read more:

Valve Tool 00
Valve Spring Tool with interchangeable components. For use on many vehicles without removing cylinder head.
read more:

Stubby 3/8 X 1/2 Ratchet 23.99
Short Pattern Double Drive 3/8 X 1/2
Flexible Head "Stubby" Ratchet
Comfortable rubber cushion grip handle Features 72 gear teeth for speed & durability Chrome vanadium steel construction.
Saves space in the tool pouch or tool box,
saves time looking for a tool
and saves money!
read more:

O2 Sensor Flex Wrench 47.99
Oxygen Sensor Flex Head Wrench
Features and Benefits:
22mm size covers 90 percent of all vehicles
Adjustable head allows for easy access to hard to reach places.
Slip the tool over the sensor without damage to wires.
Long handle provides extra torque.
TWB MK FHW02 22 Lifetime Warranty
read more:

Valve Spring Compressor 0.00
Valve spring compressor
. Allows spring compression by releasing the valve from the valve collets without removing the head.
. The tool is fixed to either the camshaft or the head walls by two hooks supplied with it
read more:

Stubby Double Ratchet 3/8 X 1/4 12.99
Stubby Short Pattern Double Drive 3/8 X 1/4
Flexible Head Ratchet
Comfortable rubber cushion grip handle Features 72 gear teeth for speed & durability Chrome vanadium steel construction.
Saves space in the tool pouch or tool box,
saves time looking for a tool
and saves money!
read more:

PenTool Elite 9.50
The PenTool Elite
How many times have you wished that you had a screwdriver handy to repair your glasses, fix a gadget or tighten a screw? We all have! That is why the PenTool Elite was created. Disguised as a pen, this a 3 in 1 multi functional hand tool. Now you can have a screwdriver handy without carrying the weight of some bulky, awkward tool. The PenTool Elite is great for the home, the office or traveling. Comfortable to hold and easy to use, this smooth writing PenTool will certainly make a great gift for anyone. In fact, you will like this PenTool so much, that you will probably want to keep it for yourself. Rotate the front of the PenTool to reveal the ink pen. Unscrew the back half to access the screwdrivers (Phillips head and flat head). Made completely of metal, the PenTool Elite is strong and durable.
read more:

Standard Length 3/8 X 1/4 Ratchet 18.99
This is a STANDARD length version
(not a stubby)
Double Drive 3/8 X 1/4
Flexible Head Ratchet
Comfortable rubber cushion grip handle Features 72 gear teeth for speed & durability Chrome vanadium steel construction.
Saves space in the tool pouch or tool box,
saves time looking for a tool
and saves money!
read more:

Standard Length 3/8 X 1/2 Ratchet 25.99
This is a STANDARD length version
(not a stubby)
Double Drive 3/8 X 1/2
Flexible Head Ratchet
Comfortable rubber cushion grip handle Features 72 gear teeth for speed & durability Chrome vanadium steel construction.
Saves space in the tool pouch or tool box,
saves time looking for a tool
and saves money!
read more:

Spreader Socket 26.99
Spreader Socket Number 3424This tool is used on all A4 platform VWs including Golf,Jetta, and Gti, 337, 20a.e. GTI model year 1999 to presentTool is used any time the strut needs to be separated from the wheel bearing housingMost common would be changing/replacing struts, coil spring, or the entire strut assemblyYou would also use this tool when servicing the wheel bearingWhy do you need to use it?? you can not easily remove the strut from the wheel bearing housing without itThe wheel bearing housing clamps down very tightly on the strut assembly....even with the bolt removed the housing is still firmly clamped to the strut...this tool allows you to spread the housing where it is clamped on so that the strut can be removed.Basically this tool is a must have any time the strut or wheel bearing housingneeds to be removed from the above models.
read more:

T Handle Ball Tip Wrenches 00
Ball head hexagon wrenches
with high torque handles, chrome plated.
Specifications: Made entirely from drawn hexagon material.
Its ball head shape allows the tool to be used with a slant of up to 30 from screw axial.
Use short part for tightening (where possible).
Accurate proportions of the ergonomic handle, according to the size of the wrench,
are synonymous with high tightening capacity, even in small areas.
read more:

Swivel Head Ratchet 19.99
Swivel Head Ratchet. 3/8" Drive swivel head. Compact, stubby design. Comfortable rubber cushion grip handle. Features 72 gear teeth for speed & durability. Chrome Vanadium steel construction.
read more:

Bit Driver and Ratchet Set 126.50
26 bits and 2 accessories in metal case.
Reversible ratchet double ended for bits (1/4X5/16)
1Magnetic bit holder with bi material handle
4Bits for slotted head screws (0,5X3 0,8X5,5 1X5,5 1,2X6,5)
6Hexagon bits for power drivers (2 3 4 5 6 8)
4Bits for cross head Phillips screws, 1/4' hexagon drives (0 1 2 3)
3Bits for cross head Pozidriv Supadriv screws (1 2 3)
9Bits for Torx head screws (T8 T9 T10 T15 T20 T25 T27 T30 T40)

read more:

Universal Valve Spring Compressor 59.99
This set is used to remove and install the valve spring
with the cylinder head still on the engine and in the car,
or with the cylinder head removed.
The multi point adjustable base of this tool bolts securely to the headwhile the adjustable lever mechanism pivots from the bar thus compressing the spring.Quick removal and installation of the spring retaining keepers is then easily accomplishedthrough the large openings on both sides of the compression tube.This set comes complete with an easy grip handle and a storage tray.
read more:

Knipex 4 in One Plier 34.99
Dont have this tool???
You need to git one!
Crimping and Stripping Pliers
Four functions in one tool!
Grip, strip, cut and crimp!
. Crimps cable links
. Strips 10/12/14 AWG wire
. Factory tested for copper / aluminum cable and hard wire
. Made of high strength special grade steel
. Plastic coated handles and polished head
. 6 1/4" overall length
read more:

Twist Out Socket Set 44.95
TWIST OUT NUT AND BOLT REMOVER SET 5PC5/16 9/16 (8 14MM)Contains five specially designed sockets that grip rounded nuts and bolts to remove with ease.Fives sizes cover the range of 5/16 to 9/16 (8mm to 14mm).Sockets are made of hardened tool steel for long life.Easy to use.
read more:

Adjustable Wrench Set 49.00
SAE Adjustable Box Wrench Set, 2 Pieces, Wrench Length 9, 11 Inches, Range 5/16 to 7/8, 1/2 to 1 1/4 Inches
Grabs the bolt on four sides to prevent slippingor bolt damage. These tools have a strong steelconstruction and they adjust to a wide range ofsizes, taking the place of many standard sizebox wrenches. Drop forged and heat treatedfor strength and durability, with a chromeplatedsatin finish.
Easy one handed side adjustment. Slightly offset for better access.
read more:

Bolt Extractor Set 34.99
5 Pc Bolt Extractor Set
Reverse spiral flutes are designed to bite down to provide maximum gripping power High carbon steel ensures longer life and greater durability Universal lobular design fits all types of fasteners 3/8" square drive for use with hand ratchets, impact wrenches, and air ratchets; hexagonal flats for use with flat wrench, pliers, adjustable wrench, sockets or VISE GRIP locking pliers.
Sizes: 5/16 (8 mm), 10 mm, 13 mm, 11/16, 3/4 (19 mm)
read more: