BMW PAGE 2
BMW
REPAIR TOOLS
OPEN 7 DAYS
A WEEK
ZDMAK TOOLS
Special Tools for BMW
Check it out....
Toll Free
877-938-6657
email: sales@zdmak.com
You are on BMW Page 2
BMW
TOOL LOT 4
Number
ZD-BMW44XWP
Included in this set:
Two Brand New
"Long Pattern" Thin Wrenches
Many applications
for thin wrenches including some of the following:
Mercedes and BMW Needed for R&R of fan clutch hub nut.
Porsche 32mm used for R&R of tie
rods Model 911 Turbo, 89 -76
36mm Needed for proper adjustment of
rear ride height 911 , 89-77
One of each Thin Wrench sizes: 36MM and 32mm
Great for work on European vehicles.
Wrenches have an overall length of 20 inches.
Thickness of each wrench is 1/4" ( 6.35mm )
Tools (wrenches) come with a rubber handle grip on each.
Plus * Double Waterpump Tool
This special tool covers most
popular applications
Used for securing Water Pump
Hub from rotating during R & R of Fan Clutch Nut
Applicable:M10, M20, M30, M40, M41, M42, M50, M60, M62
Should be
used in conjunction with a 32 or 36mm Wrench.
BONUS
The "Folding" Set above has the Tamperproof Torx heads.
(Each torx blade has a hole in the tip = Tamperproof)
The Torx sizes are: T9, T10, T15, T20, T25, T27, T30, T40
This set is GREAT for BMW,s.
Remember these are "Tamperproof - with a
hole in the tip....
VERY USEFUL
The T25 is for several applications E34 E32 E36 E39 E38 (tilt-slide sunroof)
The T30 is for most BMW with supplemental
restraint systems / SRS (BMW REF# 002110)
The T20 is for some applications on E38 (Diffusion Disc Mount)
Set Number ZD-BMW44XWP
$79.99
Vanos Turning Tool
BMW 115490
Factory Tool Made in
Germany
Sprocket Tool 115490 (Factory Ref: 90-88-6-115-490)
For turning
sprockets when removing and installing VANOS unit
Applicable: BMW Engine M50, M52, M50 US, M52 US
$38.00
30mm
thin wall deep socket
Special 30mm Thin wall
12 point, Deep Socket.
Used for the proper R&R of BMW; transmission drive shaft
flange nut and pinion drive shaft flange nut of differential.
This is a very useful high quality tool.
$39.00
Arbor
Oil Seal Installer
BMW3018
Arbor needed for the proper installation of oil seal
on pulley side of crank shaft.
Applicable: BMW engine - M20.
$29.00
Oil
Seal ARBOR
BMW3020
Arbor needed for the proper installation of radial oil seals
of gearbox output flange on Getrag gearboxes.
Applicable: BMW gearbox - G242/262, G240/260.
$34.00
BMW 3005
This handy wrench comes
with a 10mm Allen insert,
and is used for the R&R of BMW Differential Oil Plugs
Applicable: All late model BMW's.
This new design is perfect for getting the job done right.
$19.00
Clutch Wear Gauge
BMW 3004
Clutch Wear Gauge used for checking thickness of clutch disk
without removing the transmission. Applicable: BMW models ‘75 and
newer.
$20.00
Front Wheel Bearing
Hub Installer
BMW 3006
Front Wheel Bearing Hub Installer used to properly
load the axle shaft and hub into the front wheel bearing.
Applicable: BMW 3 series ‘84 and newer.
$59.00
Front Wheel Bearing
Hub Installer
BMW 3007
Front Wheel Bearing Hub Installer used to properly load the
axle shaft and hub
into the front wheel bearing. Applicable: BMW series 5, 6, 7 ‘83 and newer.
$59.00
Special Pin Wrench
BMW3036
This new hand held pin wrench was designed to remove and
install
the plastic shift coupler ring - nut, during R&R of of manual shift lever.
Made from Steel. Applicable: All BMW models ‘86 and
newer.
$21.00
Chain Tensioner
BMW113290
For secondary
chain tensioner to block chain tensioner piston
e.g. when removing
and installing sprockets
Applicable: BMW Engine M50, M52 EMAIL
$24.00
INNER
BALL JOINT REPAIR
BMW3028
Set used for proper removal and installation of inner ball
joint of control arm.
For on the car repair, requires this set to be used in conjunction with a C- Clamp.
Or to be used in conjunction with Hydraulic Press. Applicable Chassis: E30 and E36.
$147.00
BMW
E36
PRESS ARBOR KIT
CONTROL ARM - BALL JOINT TOOLS
BMW3038
For removing and installing
the outer wheel control arm ball joint.
Use it together with C-Clamp (TW 35504 or OTC 7249) on the car,
or with your hydraulic press. Applicable: E36 models.
(Ball Joint # 31126758510)
$159.00
Control Arm Press Arbor Kit
BMW3003
This set is used for the R & R of control/track arm bushings.
Used in conjunction with a hydraulic press.
Applicable: BMW cassis - E24 and E28.
$26.00
Strut
Extractor
bmw3032
This
tool is used specifically
for removal of Traction strut from TIE rod lever.
(SAME AS BMW TOOL 312140)
Applicable: Chassis - E31, E32, E34
$131.00
BMW334190
Rear Wheel Carrier R&R Set
Read
about it here
For
removing/installing ball joint at Rear Wheel Carrier (Lower Steering Knuckle).
Bushing # 33321090504, # 33321095631 (Foreign part #040060038012)
Rear Wheel Carrier R&R Set
Applicable: E38, E39
EMAIL
BMW Special 6
Point Socket
Wiper Arm Adjustment
BMW-0570KSC
This Tool is
used for R & R of windscreen wiper arm
and adjusting the pressure on: BMW E31, E38 and E39
The Torx* nut is mounted in the Wiper Arm Bearing assembly.
Item Number BMW-0570KSC
$42.50
BMW STNA1061
Cylinder Head Spanner 17mm
1/2 Drive for BMW Diesel
$63.00
Hazet BMW Tool Set Number 0-2900/204 Tool Assortment
For BMW passenger cars
- Assortment 204 Count
Average List Price: $2,905.00
Detailed Tool List Here
GERMAN CAR SPECIAL! New 12
Point (XZN) Stubby Sockets.
Number ZDXZN1008PC
Eight
Piece Set sizes: 4mm, 5, 6, 8, 10, 12,
14 and 16mm
These are new Short pattern "Stubby"
Sockets
Triple Square XZN 8 piece
Socket Set 3/8 Drive
Sturdy and compact one solid piece socket design.
Satin Chrome
with black impact tips. "New"
S2 Alloy Steel
You are on BMW Page 2
