audi special tool volkswagen special tool volvo tool bmw service reset -- mmk4mkt

Headbolt & Drain Plug Socket Set 28.00

TWO TOOLS!!!
Audi Headbolt Tool (LEFT)Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Plus Drain Plug Socket (right)Special Tamperproof Transmission Drain Plug Socket.Triple Square (12 Point XZN)Same as Volkswagen Tool 3357.For Porsche Boxster and Audi A4, A6 and Passat. Dont hesitate...these are BOTH the CORRECT tools for the job!

Audi Headbolt Toolt 17.50

This is the tool you are looking for!
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Headbolt & Drain Plug Socket Set 2 28.00

Drain Plug Socket
Plus Heabolt Tool
Details: Tamperproof Transmission Drain Plug Socket.
Triple Square (12 Point XZN)
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Plus Audi Headbolt Tool
Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Set of 2 Audi Tools from ZDMAK

Dont hesitate...these are BOTH the CORRECT tools for the job!

Audi VW Headbolt Tool Set 2 29.50

These are the tools you are looking for!VW AUDI Headbolt Tools 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi
Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tools. Please read: The T10070 is the correct current VW Audi number for this new style tool.The old tool number was 3452 and is now discontinued.Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this new style a Polydrive.

Plus you get Headbolt Tool Triple Square 12 Point (XZN) Socket M10Sturdy 1/2 Drive Tools used for a wide variety of applications including headbolts.Excellent for working on German vehicles.
This XZN tool is 5 1/2 inches long and the shaft is 4 inches.
Super set for removing & installing cylinder headbolts on both early and late model 1.8T and 2.0L gas engines. You will get both tools with this purchase.

Special Hook 3370 29.99
Factory Tool 3370
Made in Germany.
TOOL USED TO REMOVE FRONT SEAT BACK REST PANEL ON AUDI A4.
read more:

Headbolt Socket 17.50

This is the tool you are looking for.
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Super Duty Headbolt Tool 37.50

Headbolt Tool ....Read:
Same as Number T10070
Super Strong Headbolt Tool 1/2 Drive
(notice the solid one piece design)
Tool used to remove and install cylinder headbolts. New "Stronger" One Piece design. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2" Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socket The old tool number was 3452 and is now discontinued.. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. The German Tool Books call this a Polydrive. This is NOT a Torx socket although it is a 6 point tool. The points are more flat (squared off) than a torx. and it is NOT a XZN (tri square) Socket.

Pin Wrench 37.00

Heavy Duty Tensioner with Handle Grip
Same as Volkswagen number T10020
VW AUDI TENSION PULLEY SPANNER WRENCH This unique tool is for 1998 and later VW and Audi which require spanner wrench adjustments to the timing belt.Details: Special Wrench for adjusting the belt tension on the following: Audi: A6 1.6 (96 and newer) ALZ VW: Polo Classic, Golf, Bora, New Beetle 1.6 (97 ) AEH / AKL / APF / AUR /AVU / AYD Golf, Bora, New Beetle, 2.0 (98 ) AQY / APK

This is the new style Pin wrench with the (offset) angled head, same as the factory tool only this tool is a little longer for leverage with a rubber handle grip for a better feel compared to the smaller version.

Headbolt Tool Set 2 29.50

These are the tools you are looking for!
Plus they are on sale!
Headbolt Tools 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi
Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tools. Please read: The T10070 is the correct current VW Audi number for this new style tool.The old tool number was 3452 and is now discontinued.Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this new style a Polydrive.

Plus you get Headbolt Tool Triple Square 12 Point (XZN) Socket M10Sturdy 1/2 Drive Tools used for a wide variety of applications including headbolts.Excellent for working on German vehicles.
This XZN tool is 5 1/2 inches long and the shaft is 4 inches.
Super set for removing & installing cylinder headbolts on both early and late model 1.8T and 2.0L gas engines. You will get both tools with this purchase.

Super Duty Pin Wrench 37.00

New Style Headbolt Polydrive 17.50

This is the tool you are looking for!
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen AudiV6 and 4 Cylinder5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Spark Plug Boot Tool 32.99
Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket...SOME APPLICATIONS INCLUDE: 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.
read more:

Tappett Depressor 44.99

Tappet Depressor needed for preloading cam followerswhile exchanging valve adjusting shims.Applicable: Late model VW Audi 4 and 5 cylinder gas engines.More Detail: Some German Tool books have the following info on this tool...For all 4 cylinder engines with bucket tappets 1983 and Newerand all 5 and 6 Cylinder with bucket tappetsGolf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe,Audi 80 Quatro, Audi 100, 200,LT28 50D

Tappet Depressor 44.99

Tappet Depressor 2078A used for preloading cam followerswhile exchanging valve adjusting shims.Applicable: Late model VW Audi 4 and 5 cylinder gas engines.More Detail: Some German Tool books have the following info on this tool...For all 4 cylinder engines with bucket tappets FROM YEAR 1983 and Newerand all 5 and 6 Cylinder with bucket tappetsGolf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe,Audi 80 Quatro, Audi 100, 200, LT28 50D

Complete VW Audi Radio Keys 24.99

Set of Volkswagen Audi Radio Removal Tools Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
PLUS * Set Number vw 3316 Radio Removal Tools New Body Style Passat Jetta Golf Please check your manuals for details.
You will get virtually full VOLKSWAGEN coverage with this set
Plus BMW Radio Removal Tool.Pentagon shaped tool with 3 5/8 inches overall length.Applicable: Most BMWs.This Five sided driver is used to release anti theft radio mounts.YOU ALSO GET THE SPECIAL SMALL ALLEN (Right) side of picture FOR NEWER E38 & E39 7 SERIES
Plus * MERCEDES RADIO REMOVAL KEYS FOR NEWER AND OLDER VEHICLES

Pin Wrench Socket 14.99

VW524Pin Wrench Socket with 1/2" drive.This tool is used for R&R of grooved ring retaining nuton strut tower of front shock absorber. Applicable: This popular tool is used on a wide variety of VW and Audi MK1 golf and GTi , MK2 Golf & GTi 8V and 16VPolos..Audi Coupe..Audi 80 & Audi 90
Also used for adjusting power steering gear on VW Jetta, Golf, GTI.

Door Handlle Hinge Kit 79.50
Tool Kit for BENZ , VW , AUDI , PORSCHE door hinge/handle installer & remover.
Finally, a compact solution to accessing the special features found on the door hinges and door handles of VW/Audi, Mercedes Benz and Porsche, includes 4 door hinge bits (less than 1 inch long) with slender ratcheting wrench and extra long drivers for accessing Mercedes and VW door handle fasteners.
read more:

Switch Blade Radio Keys 37.50
O.E. ANTI THEFT RADIO KEY SWITCH BLADE
Radio Removal Kit Features:Special features:. Each key folds into the body handle like a pocket knife.. Each half of the tool kit allows for an even pulling action.. The two halves slide and are held together via an interlocking channel.. Every Key in the kit is current up to 2005.The full application range of this new kit is as follows:. Updated application key kit for Mercedes & all Porsche 996 and Boxster equipped withBecker radios.. Updated key combo for all Audi & VW radios up to 2004: models equipped with fourhorizontal (Audi) or two vertical slots (New Beetle, Jetta, etc.).. VW only key kit for Passat, Jetta, Golf models. This key application range ends wherekey kit 2 begins.. Five sided "pentagon" driver for most every BMW model, excluding E38 & E39 models.. Special Allen key for BMW E38 and E 39 models.. Standard "barbed hooks" (like U Hooks) for Ford, Chevy, Saab, Land Rover, etc.
read more:

ANTI THEFT RADIO KEY SET 35.99
"NEW"
O.E. ANTI THEFT
RADIO KEY SWITCH BLADE STYLE
Radio Removal Kit Features:
Special features:. Each key folds into the body
handle like a pocket knife.
. Each half of the tool kit allows for an even pulling action.
. The two halves slide and are held together
via an interlocking channel.
. Every Key in the kit is current up to 2005.
The full application range of this new kit is as follows:
. Updated application key kit for Mercedes & all Porsche 996
and Boxster equipped withBecker radios.
. Updated key combo for all Audi & VW radios up to 2004:
models equipped with fourhorizontal (Audi) or two vertical slots (New Beetle, Jetta, etc.).
. VW only key kit for Passat, Jetta, Golf models. This key application range ends wherekey kit 2 begins.
. Five sided "pentagon" driver for most every BMW model, excluding E38 & E39 models.
. Special Allen key for BMW E38 and E 39 models.
. Standard "barbed hooks" (like U Hooks) for Ford, Chevy, Saab, Land Rover, etc.
read more:

Audi VW Headbolt Tool 32.99

Polydrive Cylinder Head Socket for VW/Audi.
This fits in the new special profile. Ref: Volkswagen number T10070.
This is not a torx and it is not a cheesehead or triple square. This is called Polydrive.
The overall length is 168mm. Shaft length is 130.
Super High Quality Tools Made in Germany by Hazet!

Radio Removal Set 24.99

Valve Spring Tool & Bridge 142.50

Valve Tools (2)
Set including:Valve Spring Compressor Bar
Same as Volkswagen Tool Number VW 541/1
Used for R&R of valve spring or rocker armWith this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool BridgeApplicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker armUsed in conjunction with tool VW541/1Applicable: Model 924. VW / AUDI 4 5 Cyl.

Tappet Depressor Set 81.50

VW546 Tappet Depressor Tappet Depressor used for preloading cam followers. For Bucket Tappets on VW Golf, Jetta, Caddy, Scirocco, Passat up to 1982 Also Audi 80 , 100

Plus 2078A Tappet Depressor needed for preloading cam followers while exchanging valve adjusting shims. Applicable: Late model VW Audi 4 and 5 cylinder gas engines. More Detail: Some German Tool books have the following info on this tool... For all 4 cylinder engines with bucket tappets 1983 and Newer and all 5 and 6 Cylinder with bucket tappets Golf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe, Audi 80 Quatro, Audi 100, 200, LT28 50D.

Valve Spring Tool and Bridge 142.50

Valve Spring Tools Set including:VA6010Valve Spring Compressor BarSame as Volkswagen Tool Number VW 541/1Used for R&R of valve spring or rocker armWith this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool BridgeApplicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker armUsed in conjunction with tool VW541/1Applicable: Model 924. VW / AUDI 4 5 Cyl.

Spark Plug Boot Tool 24.99

Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket on 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.

Best Seller ! Radio Tools Set 24.99

This is one of the best sets on the market. This is a Master Set for BMW Mercedes Porsche VW Audi and DIN. Included is a total of 3 different sets Volkswagen Audi, two different tools for BMWand a set for Mercedes Porsche and a DIN Ford set. The VW Tools (4) Number T10057Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box. If you have 4 slots VW AUDI this is the 4 keys you need) Plus you get Number VW 3316 (2) Radio Removal Tools New Body Style Passat Jetta Golf . You will get virtually full coverage forVolkswagen Audi when you buy this master set. The BMW Radio Removal Tools areone Pentagon shaped tool with a 3 5/8 inches overall length. Applicable: Most BMWs. This Five sided driver is used to release anti theft radio mounts.You will also get the special rare small allen tool for BMW (upper left) Fornewer BMW E38 & E39 7 SERIES Plus Mercedes most coverage for newer and oldervehicles, especially 1992 and newer 129, 140, 163, 202 & 210 PLUS Range Rover with Becker Nav System.The MB Tools also work on Porsche. Appl: Turbo GT, GT2, GT3, Boxster, Cayenne 911, 996 , 987, Carrera etc. Same as Porsche ref: 000 721 957 01

Special Hook 3370 30.00

Factory Tool 3370
Made in Germany.
TOOL USED TO REMOVE FRONT SEAT BACK REST PANEL ON AUDI A4.

Hazet Tensioning Tool 75.98

Driving Tool for Tensioning Device
special steel, for operating devicewhen changing the V ribbed belt,especially on VW Polo, Golf and Passat, AUDI since 1991.

Grand Master! Radio Tool Set 34.99

Master Radio Removal Tool Set
18 Piece Set includes the following tools needed to install and remove radios :. 2pc. Radio Removal U Hook (Ford/VW/Audi/Grundig/Blaupunkt) . 1pc. Special Pentagon Wrench (BMW). 4pc. Radio Removal Keys (VW/Audi/Becker/Mercedes Benz) . 2pc. Radio Removal Keys (Mercedes Benz/Porsche/Becker). 2pc. Radio Removal Keys (VW). 1pc. Allen Hex Wrench (BMW/Opel). 2pc. Radio Removal Keys (New Becker). 2pc. Radio Removal Keys (New Skoda). 2pc. Radio Removal U Hook (New Blaupunkt)

Triple Square Drain Plug Tool 49.50

This is a Special Tamperproof * Transmission Drain Plug Socket. Triple Square ( 12 Point XZN 16) Same as old Volkswagen Tool 3357. (Number 3357 is still found in many/most manuals for this job)
Applicable Porsche Boxster and Audi A4 A6 and Passat. This is an excellent high quality tool Made in Germany. Plug not included, picture is for reference only.

Power Steering Waterpump Pulley Tool 24.00

VA6024Power Steering and Waterpump Pulley Removal & Replacement Tool Volkswagen AudiUsed to hold the power steering or water pump pulley stationarywhile removing or replacing the three socket headbolts that attach pulley to the shaft.Tool is designed to be used on pulleys that utilize these socket head bolts.Applications:VW Audi 4 cylinder water cooled gas or diesel engines from 1975 to current.Volkswagen V6 1992 and newer.Audi power steering pump pulley V8 1990 and newer.Audi V6 1992 to current.Also VW 1983 to 1988 and Audi 1981 to 1995 with socket head boltsholding the pulley to power steering pump.

Drainplug Tool on Sale! 14.99

Drain Plug Socket
This is a Special Tamperproof Transmission Drain Plug Socket.
Triple Square ( 12 Point XZN )
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

PULLEY HOLDING TOOL 74.99

AUDI & VW
FAN CLUTCH PULLEY HOLDING TOOL
AUDI 1996 2001 A6 2.8L V 6 & VW 1998 & later Passat 3.0L V 6

Thin Head Flexible Ratchet 79.99
Ever see this one? It is a Super Tool....
A flexible "Thin Head" Reversible bit holding Ratchet.
(the reverse mechanism is on the flip side of photo not shown)
The head will flex backwards forwards more than a 90 degree (70 to 80)
The thickness of the head is 10mm
The overall length is 164mm ( 6 1/2 inch).
This tool is great for getting into a tight spot with a special bit,
during rare or difficult procedures (bits not included)
Call if you are looking for a special bit to go with the tool.
read more:

Special Open Socket 22mm 25.00

On Sale *
22mm Special TubeSocket
1.) Used for securing the Strut tower retaining nut of most European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench)
2.) R&R of Oxygen Sensor.
Also for R&R of some Mercedes Diesel injectors ( OM604, 605 & 606).
Details: For removing and installing front strut unit on VW Golf up to 1988, Jetta up to 87, Scirocco, Audi 80 and Golf 3 from 1993 newer, Passat from 88 and newer, Audi 100, 200 Coupe and Quatro.
This tool is often used in conjunction with a 7mm hex wrench.
Clickhere for a picture of the tools in action: 

Cooling System Adapter 15.50

VOLKSWAGEN AUDI
COOLING SYSTEM ADAPTER
APPLICABLE:
VW AUDI WITH MALE THREADSON FILLER NECK OF EXPANSION TANK
(VW ALL PRE 90 / AUDI ALL PRE 90)
THIS IS A QUALITY TOOL MADE IN EUROPE

Best Quality XZN Size M16 49.50

This is a Special Tamperproof Transmission Drain Plug Socket. Triple Square ( 12 Point XZN 16) Same as old Volkswagen Tool 3357. (Number 3357 is still found in many/most manuals for this job)
Applicable Porsche Boxster and Audi A4 A6 and Passat. This is an excellent high quality tool Made in Germany.
* Plug not included, picture is for reference only.

Special Rivet Tool 0.00
Special Rivet Tool
Plier with 90 degree rotating head.
Tool used to remove two piece reusable plastic rivets
found on door panels, engine shields, wheel well shields etc.
For undivided rivets the Plier can also be used for cutting the head off the rivet.
Easy to use universal Plier eliminates damage to trim and door facings.
read more:

Tri Square Drain Plug XZN 49.50

Pin Wrench Set 2 49.00

This is the Best Quality Set of the two CRUCIAL VW Audi Pin Wrenches you will find anywhere.
SUPER HIGH QUALITY TOOLS (BOTH) MADE IN GERMANY BY HAZET.
First item is number V159 (this is a smaller tool on the left side picture is not to scale) This tool is for easy adjustment of Camshaft spur belts
(toothed belt) on idler pulleys with Pin holes. This wrench with its protruding pins, grabs the center
of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment.
Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80
Distance of pins 18 mm, diameter of pins 2.9 mm for deep located idler pulley
on toothed belt on 1,6 l diesel engine VW van T3 (up to model 1991).
V159 is the correct number the old VW Number on this (smaller) tool was 2587.

T10020 Special wrench with an offset (angled) head (Larger tool on right side of image)
This tool also used for adjusting timing belt tension.
99 and later VW Golf, VW Jetta and Beetle with 2.0 Litre Gas and 1.9 Litre TDI Engines.1999 and newer Golf, Jetta
New Beetle with 2.0l gas engine and 1.9l T.D.I. Diesel engine. You will get both tools with this purchase.

Volkswagen Door Tool 9.99

T10011Volkswagen Door Tool triple Square 4
This is the correct tool for the job
New Beetle Tool This tool is used for R & R of door handle screws.Applicable: 1998 & newer VW Golf, Jetta, Passat & New Beetle....possibly other VW Audi.
This tool is a high quality item you will like.

10mm Glow Plug Tool 69.99

10mm Universal Glow Plug Socket mainly for VW Audi Diesel Injection TDI 3/8 Drive.
High quality tool
Made in Germany by Hazet!
DETAILS: ALFA ROMEO, AUDI, CHRYSLER, FIAT, FORD, MERCEDES, LAND ROVER, RENAULT, SEAT, VOLKSWAGEN.

Brake Piston Tool 14.99

Disc Brake Piston Cube Tool has 5 different drive pin configurations designed to rotate the parking brake activated piston back into the caliper cylinder when replacing worn pads on vehicles equipped with 4 wheel disc brakes. Tool will service many domestic and import cars. This tool will work in place of special tool 3272. Some Audi VW calipers (mid 80s) use a hex tool check yours to be certain a pain in the neck if you have never done them before. Grind or file off two diagonally opposite corner pins to allow the cube to fit the vw rear brake piston. Use with a 3/8" ratchet. It can be easier to fasten the rear caliper back onto the carrier without the rotor in place while using this tool. That way you get a little extra leverage. Use as follows: engage the two prongs and turn the piston 180 clockwise. Remove the tool. Use a generic calper tool or a c clamp and push the piston in about 2mm. Keep alternating back and forth between the cube tool and the c clamp until the piston in almost all the way in. If you are strong enough, you may not even need the c clamp just push with the cube tool as you turn. Instead of the cube, you can even use needle nose pliers, but then you defintiely need the c clamp. The rear brakes can be rather difficult, so make sure you have plenty of time. Also for use on most popular imports and Chrysler, Ford and GM vehicles with 4 wheel disc brakes.

Hazet Quality Tools 75.98

Driving Tool for Tensioning Device
special steel, for operating devicewhen changing the V ribbed belt,especially on VW Polo, Golf and Passat, AUDI since 1991.

17 x 17 Injection Wrench 39.50
Double Ended Flare Nut Box Wrench Size 17 x 17mmOverall Length 241mm (9.5 inch)For injection pipes on Volkswagen / Audi This tool will help you when you remove and install the fuel lines from the injection pump and the injectors themselves.For TDI: You will still need to torque the 17mm fittings down to spec, but this tool will make taking the fittings off a snap, as well as putting them back on.This is a Factory Tool Made in Germany
read more:

Bonus Triple Square Set 5 49.99

12 Point Headbolt Tools Plus Drain Plug Socket. (Anyone looking knows how hard it is to find a good price on XZN Tools here you have the extremely popular size 10 and more...)
The Headbolt Set of 4 Includes: 6mm, 8mm, 10mm & 12mm
with 3/8 Drive holders on a rail.
Plus you get
Drain Plug Socket (Upper Left)
Special Large size M16
(Notice the Tamperproof Center on the M16)
Drain Plug Socket Triple Square (12 Point = XZN )
For Porsche Boxster and Audi A4, A6 and Passat
A very handy set for the VW, Audi, Porsche and German car mechanic.

Note: The 4 pieces (Right) are regular XZN and the drainplug tool is tamperproof.
You will get all five pieces with this purchase.

Holding Tool and Wrench Set 49.99

Set of 3 Includes:
Double Waterpump Tool*
This special tool covers most popular applications
Used for securing Water Pump Hub from rotating during R & R of Fan Clutch Nut
Applicable:M10, M20, M30, M40, M41, M42, M50, M60, M62

Plus
2 Long Pattern Thin Wrenches
German Car Special Tools
One of each size: 36mm and 32mm
Overall length of 15 inches.
Thickness of each wrench is 8mm.

Optical Tester Made in Germany 0.00
Super Optical Tester
Cooling System Special Tool
Hazet 4810 Made in Germany
for controlling the anti freezing acid concentration
in the cooling system, as well as for cooling fluid G11 and G12
VOLKSWAGEN/AUDI and the battery acid concentration (battery charging).
read more:

Ferrari Head Bolt Tool 44.00
Special 8 Point
Offset ring Wrench for Headbolts.
Available 15mm or 17mm both come 1/2 inch drive.
The overall length of the tool will be 274mm.
read more:

T45 Torx with U Joint 14.99

Torx size T45 Universal Joint Special Tool Torx T45 used for upper door hinge and other applications.VW Volkswagen Audi repair.Satin Chrome plated 3/8 drive

You Searched for

audi special tool

Trade Links With ZDMAK