audi part tool SARASOTA audi part tool vw part tool -- mmk4mkt

Spark Plug Boot Tool 32.99
Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket...SOME APPLICATIONS INCLUDE: 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.
read more:

Tappett Depressor 44.99

Tappet Depressor needed for preloading cam followerswhile exchanging valve adjusting shims.Applicable: Late model VW Audi 4 and 5 cylinder gas engines.More Detail: Some German Tool books have the following info on this tool...For all 4 cylinder engines with bucket tappets 1983 and Newerand all 5 and 6 Cylinder with bucket tappetsGolf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe,Audi 80 Quatro, Audi 100, 200,LT28 50D

Audi Headbolt Toolt 17.50

This is the tool you are looking for!
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Tappet Depressor 44.99

Tappet Depressor 2078A used for preloading cam followerswhile exchanging valve adjusting shims.Applicable: Late model VW Audi 4 and 5 cylinder gas engines.More Detail: Some German Tool books have the following info on this tool...For all 4 cylinder engines with bucket tappets FROM YEAR 1983 and Newerand all 5 and 6 Cylinder with bucket tappetsGolf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe,Audi 80 Quatro, Audi 100, 200, LT28 50D

Headbolt & Drain Plug Socket Set 2 28.00

Drain Plug Socket
Plus Heabolt Tool
Details: Tamperproof Transmission Drain Plug Socket.
Triple Square (12 Point XZN)
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Plus Audi Headbolt Tool
Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Set of 2 Audi Tools from ZDMAK

Dont hesitate...these are BOTH the CORRECT tools for the job!

Pin Wrench Socket 14.99

VW524Pin Wrench Socket with 1/2" drive.This tool is used for R&R of grooved ring retaining nuton strut tower of front shock absorber. Applicable: This popular tool is used on a wide variety of VW and Audi MK1 golf and GTi , MK2 Golf & GTi 8V and 16VPolos..Audi Coupe..Audi 80 & Audi 90
Also used for adjusting power steering gear on VW Jetta, Golf, GTI.

Audi VW Headbolt Tool Set 2 29.50

These are the tools you are looking for!VW AUDI Headbolt Tools 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi
Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tools. Please read: The T10070 is the correct current VW Audi number for this new style tool.The old tool number was 3452 and is now discontinued.Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this new style a Polydrive.

Plus you get Headbolt Tool Triple Square 12 Point (XZN) Socket M10Sturdy 1/2 Drive Tools used for a wide variety of applications including headbolts.Excellent for working on German vehicles.
This XZN tool is 5 1/2 inches long and the shaft is 4 inches.
Super set for removing & installing cylinder headbolts on both early and late model 1.8T and 2.0L gas engines. You will get both tools with this purchase.

Headbolt Socket 17.50

This is the tool you are looking for.
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Valve Spring Tool & Bridge 142.50

Valve Tools (2)
Set including:Valve Spring Compressor Bar
Same as Volkswagen Tool Number VW 541/1
Used for R&R of valve spring or rocker armWith this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool BridgeApplicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker armUsed in conjunction with tool VW541/1Applicable: Model 924. VW / AUDI 4 5 Cyl.

Super Duty Headbolt Tool 37.50

Headbolt Tool ....Read:
Same as Number T10070
Super Strong Headbolt Tool 1/2 Drive
(notice the solid one piece design)
Tool used to remove and install cylinder headbolts. New "Stronger" One Piece design. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2" Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socket The old tool number was 3452 and is now discontinued.. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. The German Tool Books call this a Polydrive. This is NOT a Torx socket although it is a 6 point tool. The points are more flat (squared off) than a torx. and it is NOT a XZN (tri square) Socket.

Tappet Depressor Set 81.50

VW546 Tappet Depressor Tappet Depressor used for preloading cam followers. For Bucket Tappets on VW Golf, Jetta, Caddy, Scirocco, Passat up to 1982 Also Audi 80 , 100

Plus 2078A Tappet Depressor needed for preloading cam followers while exchanging valve adjusting shims. Applicable: Late model VW Audi 4 and 5 cylinder gas engines. More Detail: Some German Tool books have the following info on this tool... For all 4 cylinder engines with bucket tappets 1983 and Newer and all 5 and 6 Cylinder with bucket tappets Golf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe, Audi 80 Quatro, Audi 100, 200, LT28 50D.

Valve Spring Tool and Bridge 142.50

Valve Spring Tools Set including:VA6010Valve Spring Compressor BarSame as Volkswagen Tool Number VW 541/1Used for R&R of valve spring or rocker armWith this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool BridgeApplicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker armUsed in conjunction with tool VW541/1Applicable: Model 924. VW / AUDI 4 5 Cyl.

Spark Plug Boot Tool 24.99

Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket on 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.

Headbolt & Drain Plug Socket Set 28.00

TWO TOOLS!!!
Audi Headbolt Tool (LEFT)Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Plus Drain Plug Socket (right)Special Tamperproof Transmission Drain Plug Socket.Triple Square (12 Point XZN)Same as Volkswagen Tool 3357.For Porsche Boxster and Audi A4, A6 and Passat. Dont hesitate...these are BOTH the CORRECT tools for the job!

Power Steering Waterpump Pulley Tool 24.00

VA6024Power Steering and Waterpump Pulley Removal & Replacement Tool Volkswagen AudiUsed to hold the power steering or water pump pulley stationarywhile removing or replacing the three socket headbolts that attach pulley to the shaft.Tool is designed to be used on pulleys that utilize these socket head bolts.Applications:VW Audi 4 cylinder water cooled gas or diesel engines from 1975 to current.Volkswagen V6 1992 and newer.Audi power steering pump pulley V8 1990 and newer.Audi V6 1992 to current.Also VW 1983 to 1988 and Audi 1981 to 1995 with socket head boltsholding the pulley to power steering pump.

Headbolt Tool Set 2 29.50

These are the tools you are looking for!
Plus they are on sale!
Headbolt Tools 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi
Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tools. Please read: The T10070 is the correct current VW Audi number for this new style tool.The old tool number was 3452 and is now discontinued.Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this new style a Polydrive.

Plus you get Headbolt Tool Triple Square 12 Point (XZN) Socket M10Sturdy 1/2 Drive Tools used for a wide variety of applications including headbolts.Excellent for working on German vehicles.
This XZN tool is 5 1/2 inches long and the shaft is 4 inches.
Super set for removing & installing cylinder headbolts on both early and late model 1.8T and 2.0L gas engines. You will get both tools with this purchase.

PULLEY HOLDING TOOL 74.99

AUDI & VW
FAN CLUTCH PULLEY HOLDING TOOL
AUDI 1996 2001 A6 2.8L V 6 & VW 1998 & later Passat 3.0L V 6

Pin Wrench 37.00

Heavy Duty Tensioner with Handle Grip
Same as Volkswagen number T10020
VW AUDI TENSION PULLEY SPANNER WRENCH This unique tool is for 1998 and later VW and Audi which require spanner wrench adjustments to the timing belt.Details: Special Wrench for adjusting the belt tension on the following: Audi: A6 1.6 (96 and newer) ALZ VW: Polo Classic, Golf, Bora, New Beetle 1.6 (97 ) AEH / AKL / APF / AUR /AVU / AYD Golf, Bora, New Beetle, 2.0 (98 ) AQY / APK

This is the new style Pin wrench with the (offset) angled head, same as the factory tool only this tool is a little longer for leverage with a rubber handle grip for a better feel compared to the smaller version.

Super Duty Pin Wrench 37.00

New Style Headbolt Polydrive 17.50

This is the tool you are looking for!
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen AudiV6 and 4 Cylinder5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Cooling System Adapter 15.50

VOLKSWAGEN AUDI
COOLING SYSTEM ADAPTER
APPLICABLE:
VW AUDI WITH MALE THREADSON FILLER NECK OF EXPANSION TANK
(VW ALL PRE 90 / AUDI ALL PRE 90)
THIS IS A QUALITY TOOL MADE IN EUROPE

Special Hook 3370 29.99
Factory Tool 3370
Made in Germany.
TOOL USED TO REMOVE FRONT SEAT BACK REST PANEL ON AUDI A4.
read more:

Complete VW Audi Radio Keys 24.99

Set of Volkswagen Audi Radio Removal Tools Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
PLUS * Set Number vw 3316 Radio Removal Tools New Body Style Passat Jetta Golf Please check your manuals for details.
You will get virtually full VOLKSWAGEN coverage with this set
Plus BMW Radio Removal Tool.Pentagon shaped tool with 3 5/8 inches overall length.Applicable: Most BMWs.This Five sided driver is used to release anti theft radio mounts.YOU ALSO GET THE SPECIAL SMALL ALLEN (Right) side of picture FOR NEWER E38 & E39 7 SERIES
Plus * MERCEDES RADIO REMOVAL KEYS FOR NEWER AND OLDER VEHICLES

Volkswagen Door Tool 9.99

T10011Volkswagen Door Tool triple Square 4
This is the correct tool for the job
New Beetle Tool This tool is used for R & R of door handle screws.Applicable: 1998 & newer VW Golf, Jetta, Passat & New Beetle....possibly other VW Audi.
This tool is a high quality item you will like.

10mm Glow Plug Tool 69.99

10mm Universal Glow Plug Socket mainly for VW Audi Diesel Injection TDI 3/8 Drive.
High quality tool
Made in Germany by Hazet!
DETAILS: ALFA ROMEO, AUDI, CHRYSLER, FIAT, FORD, MERCEDES, LAND ROVER, RENAULT, SEAT, VOLKSWAGEN.

17 x 17 Injection Wrench 39.50
Double Ended Flare Nut Box Wrench Size 17 x 17mmOverall Length 241mm (9.5 inch)For injection pipes on Volkswagen / Audi This tool will help you when you remove and install the fuel lines from the injection pump and the injectors themselves.For TDI: You will still need to torque the 17mm fittings down to spec, but this tool will make taking the fittings off a snap, as well as putting them back on.This is a Factory Tool Made in Germany
read more:

FENDER PROTECTOR 0.00

FENDER PROTECTOR FOR AUDI
PREVENTS DAMAGE TO FRONT QUARTER PANELS ON AUDI VEHICLES DURING REPAIR. COVER WILL NOT SCRATCH VEHICLE. SUITABLE FOR ALL AUDI MODELS * EXCEPT AUDI TT

Radio Removal Set 24.99

Best Seller ! Radio Tools Set 24.99

This is one of the best sets on the market. This is a Master Set for BMW Mercedes Porsche VW Audi and DIN. Included is a total of 3 different sets Volkswagen Audi, two different tools for BMWand a set for Mercedes Porsche and a DIN Ford set. The VW Tools (4) Number T10057Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box. If you have 4 slots VW AUDI this is the 4 keys you need) Plus you get Number VW 3316 (2) Radio Removal Tools New Body Style Passat Jetta Golf . You will get virtually full coverage forVolkswagen Audi when you buy this master set. The BMW Radio Removal Tools areone Pentagon shaped tool with a 3 5/8 inches overall length. Applicable: Most BMWs. This Five sided driver is used to release anti theft radio mounts.You will also get the special rare small allen tool for BMW (upper left) Fornewer BMW E38 & E39 7 SERIES Plus Mercedes most coverage for newer and oldervehicles, especially 1992 and newer 129, 140, 163, 202 & 210 PLUS Range Rover with Becker Nav System.The MB Tools also work on Porsche. Appl: Turbo GT, GT2, GT3, Boxster, Cayenne 911, 996 , 987, Carrera etc. Same as Porsche ref: 000 721 957 01

World Class Hazet Tools 0.00

Number 2593 28 Shock absorber cartridge socket 295mm long. For Audi 80 from 1992 on and Audi 90 from 1987.
1/2 inch drive.
High Quality Tool Made in Germany.

Cylinder Head Tool Kit 23.50
Cylinder Head Alignment Kit Same as Volkswagen Tool 3070
Set comes with (2) pairs of guide pins, 11X1.75mm and 12X1.75mm.VW model Scirocco, Rabbit, Dasher, Fox. Audi model 4000, 5000
read more:

Chain Adjuster 24.50

3366CHAIN ADJUSTER Required to change the troublesome cam adjuster seal
Audi and Volkswagen 4, 6 (2.7 and 2.8) and 8 CylWith 5 Valve per Cyl.
Also Audi VW 1.8 Golf Jetta Passat New Beetle
Note:The manual says to remove both camshafts to change the seal ...
but using this tool you can relieve the tension on the camshaft chainand lift it up far enough to clean, remove and replace the gasket and seal.
This procedure not only saves time but saves any other damagethat may happen to camshafts and bearings by removing them.
ORIGINAL MATRA FACTORY TOOL MADE IN GERMANY

Bar and Pin for 5 Valve 139.50

Camshaft Timing Tool Set (2)
TOOL REF 3391
Cam/Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 2002 4 cam.

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6Please note: 3391 for 5 valves per cylinder.

Valve Spring Tool 68.00

Valve Spring Compressor Bar VA6010 Used for R&R of valve spring or rocker arm VW AUDI 4 / 5 Cylinder.With this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool VA6022 below Applicable: 924 / 944Reference VW Tool Number VW541/1

Door Handlle Hinge Kit 79.50
Tool Kit for BENZ , VW , AUDI , PORSCHE door hinge/handle installer & remover.
Finally, a compact solution to accessing the special features found on the door hinges and door handles of VW/Audi, Mercedes Benz and Porsche, includes 4 door hinge bits (less than 1 inch long) with slender ratcheting wrench and extra long drivers for accessing Mercedes and VW door handle fasteners.
read more:

Crankshaft Pulley Tool 84.50

Crankshaft Tool 2084 Counter Holder Used for R & R of Front Crankshaft PulleyApllicable: VW Audi with 5 Cylinder.80, 90 Quattro, 400, 5000 QuantumUsed in conjunction with tool 2079

2 Pins and 2 Plates 103.00

2 Pins and 2 Plates Set of four tools.VW Audi T.D.I. and New Beetle Cam Kit Reference numbers for the two tools on the left are: 3418 and 3359. Tool Set for factory correct and trouble free installations. This is a popular set for Diesel timing of Bosch injection pumps. This set has been developed for aligning the cam shaft with the Diesel pump on 1998 and newer VW models equipped with a T.D.I. engine. This two piece lock plate and alignment pin allows the technician for factory correct and trouble free installations.

Tools on the right side of image are Diesel Lock Plate / Cam Setting Bar Same as Volkswagen ref 2065a Tool used for securing the cam shaft from rotating and maintaining correct timing position engine AAZ during R&R of cam shaft drive belt. Applicable: VW/Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 Lock Pin for Diesel (Same as VW tool 2064). Tool used for securing Bosch diesel injection pump sprocket from rotating during R&R of cam shaft drive belt. This Locking Pin also assists in locating the general timing position of pump. Volkswagen Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 All 4 tools are High Quality Made in Europe!

Audi Info and Timing 0.00

There are three main Cam bars for timing.
3391, 3243 and T40005
(T40005 is for V 8)
Notice the tool number 3242 this is the T.D.C (TOP DEAD CENTER) Pin
This pin goes with 3391 or 3243.
Type your selection in the search or you can find the tools in this Audi section.
Feel free to call me or email. I will try to assist you.
Please note:
In order to make your selection you must determine if your vehicle is 2 valve per cylinder or 5 valve per cylinder or V8. Example = Notice tool number 3391 says it is for 5 valve. The 3243 is for 2 valve per cylinder.

Big Mak 126.00
Master Kit
Set of 6 Tools
Including Dial Indicator

Set Includes:
3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: Volvo and VW / Audi diesels Excluding TDI
PLUS: VA6015 Holder used for accurate adjustment of Bosch diesel injection pump.
Plus: 2065A Diesel Camshaft Locking Plate Tool
PLUS: 2064 Lock Pin for Diesel.
Plus the Pin Wrench (made in Germany) for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment. Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80.
Plus Dial Indicator
read more:

Audi VW Headbolt Tool 32.99

Polydrive Cylinder Head Socket for VW/Audi.
This fits in the new special profile. Ref: Volkswagen number T10070.
This is not a torx and it is not a cheesehead or triple square. This is called Polydrive.
The overall length is 168mm. Shaft length is 130.
Super High Quality Tools Made in Germany by Hazet!

Red X Dog for Volkswagen Audi 189.99

ZDMAK D023XREDXDOG LITEOFF One of the most popular versions ofVAG (VW/Audi/Seat/Skoda/Ford) reset tool.First, it provides you with the capability of resetting the oil serviceand inspection service reminder displays. In addition, you can also reset all fault codes,(both those with and without a dashboard indicator) on all vehicle systems.Applicable: All vehicles with digital diagnostic systems.

Grand Master! Radio Tool Set 34.99

Master Radio Removal Tool Set
18 Piece Set includes the following tools needed to install and remove radios :. 2pc. Radio Removal U Hook (Ford/VW/Audi/Grundig/Blaupunkt) . 1pc. Special Pentagon Wrench (BMW). 4pc. Radio Removal Keys (VW/Audi/Becker/Mercedes Benz) . 2pc. Radio Removal Keys (Mercedes Benz/Porsche/Becker). 2pc. Radio Removal Keys (VW). 1pc. Allen Hex Wrench (BMW/Opel). 2pc. Radio Removal Keys (New Becker). 2pc. Radio Removal Keys (New Skoda). 2pc. Radio Removal U Hook (New Blaupunkt)

Cam Bar and Pin for 2 Valve 139.50

Camshaft TimingTool Set (2)
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4  94 97 AFC Engine

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6

Please note: 3243 for 2 valves per cylinder. 

Cam Bar and Pin for 2 Valve 139.50

Insulated Driver Set Made in Germany 48.50
Professional Quality Insulated Tool Set.Individually Tested Tools Certified To 1000 Volts.Tools Meet The Following Safety Specifications:ASTM F 1505 01 IEC 900 VDE 0682/Part 201 ISO 9001Certified Tools Meet OSHA Definition For Insulated Tool Requirements.Quality Tools Made In GermanyCVM Tool Steel Hardened To Average 58/60RC. 10 Piece Insulated Screwdrivers
Set Includes:Slotted: 2.0, 2.5, 3.0, 3.5, 4.5, 6.5 Phillips: 0, 1, 2, 3
read more:

Tie Rod Tool 49.99

Tie Rod Tool VW 1014Separator used for disassembly of pitman arm type tie rod endswithout tearing the ball joint boots. Opening size is 25mm.Most VW Audi & Late Porsche models.
Clickhere for a Diagram on this tool.

Set 2 Alternator Tools 47.00

Combo Socket Set of 2 consisting of the 17mm Multi Spline Adapter and XZN (12 Point) Socket size M10 for mounting and dismounting the alternator pulley at the generator.Volkswagen Audi Mercedes Porsche etc...For mounting the V belt pulley (slip clutch pulley) at the alternator (manuals call it a generator), especially for T.D.I. VW Golf III, Vento, Passat and AUDI A 3 .
The short serrated socket (3400) is size 17MM outside diameter and Length is 30mm.
The larger tool is M10 XZN triple square and is 1/2 drive x 140mm Length.Also for Boxster. (See repair Group 27 (Porsche Bulletins) Boxster Alternators with free wheeling Pulleys. High Quality Tool

Also: 1990 to 1994 porsche C2 and C4 and all porsche 993s use a (M10) 10mm 12point socket tool to hold the alternator shaft when replacing the belts the area between the alternator and car body is very limited a 10mm 12point spanner style wrench works well for this job.

Holder ONLY 37.50
Dial Gauge Holder VA6015Diesel Tool Used for accurate adjustment of Bosch diesel injection pump. (SAME AS VW TOOL 2066)
I only sell one holder (size) and this is it...same as 2066)
This Dial Gauge Holder screws into the back of theinjection pump and comes equipped with a 10cm dial indicator extension pin. This tool is to be used in conjunction with a dial indicator (not included).All VW Audi diesel and Volvo D24 6 cylinder 2.4L diesel 1981 86 engines. This holder will only work with a dial guage with a shank size of 8mm or less.
It will NOT work with a lager shank.
read more:

VW Audi Set Valve Tools 49.99

Two (2) Valve Adjusting Tools
Valve Shim Tool (10 208) Used for proper R&R of valve adjusting shims.
Applicable: Overhead Cam engines with adjusting shims
Plus
VW546 Tappet Depressor Tappet Depressor used for preloading cam followers.
For Bucket Tappets on VW Golf, Jetta, Caddy, Scirocco,
Passat up to 1982 Also Audi 80 , 100

Special Hook 3370 30.00

Factory Tool 3370
Made in Germany.
TOOL USED TO REMOVE FRONT SEAT BACK REST PANEL ON AUDI A4.

You Searched for

audi part tool

Trade Links With ZDMAK