Brake Piston Tool SARASOTA Brake Piston Tool porsche engine tools -- mmk4mkt

Brake Pad Spreader 11.99
Disk Brake Pad Spreader
Tool used for changing brake pads easy!
The tool compresses inner brake pad, resets piston for easy pad replacement.
Durable heavy duty construction.
read more:

Brake Piston Tool Set 0.00
Tool for rotating and pushing back brake pistons,
. The adaptor and adjusting screw can be rotated simultaneously to rotate and push back brake pistons, without damaging threads.. Also suitable for brake calipers without any handbrake mechanism.. Supplied with 3 adaptors
read more:

Brake Piston Tool 14.99

Disc Brake Piston Cube Tool has 5 different drive pin configurations designed to rotate the parking brake activated piston back into the caliper cylinder when replacing worn pads on vehicles equipped with 4 wheel disc brakes. Tool will service many domestic and import cars. This tool will work in place of special tool 3272. Some Audi VW calipers (mid 80s) use a hex tool check yours to be certain a pain in the neck if you have never done them before. Grind or file off two diagonally opposite corner pins to allow the cube to fit the vw rear brake piston. Use with a 3/8" ratchet. It can be easier to fasten the rear caliper back onto the carrier without the rotor in place while using this tool. That way you get a little extra leverage. Use as follows: engage the two prongs and turn the piston 180 clockwise. Remove the tool. Use a generic calper tool or a c clamp and push the piston in about 2mm. Keep alternating back and forth between the cube tool and the c clamp until the piston in almost all the way in. If you are strong enough, you may not even need the c clamp just push with the cube tool as you turn. Instead of the cube, you can even use needle nose pliers, but then you defintiely need the c clamp. The rear brakes can be rather difficult, so make sure you have plenty of time. Also for use on most popular imports and Chrysler, Ford and GM vehicles with 4 wheel disc brakes.

Saab Brake Piston Turning Tool 25.50

Turning Tool needed for rotating the piston backinto the brake caliper when replacing brake pads.Applicable: Saab models '87 and older. Excluding 9000 series

ZDMAK SPECIAL 2 Brake Tools 49.95

This sale is for two brake tools.
First tool on the UPPER LEFT is Drift Pin 4mm
Tool used for removing disc brake pads.
This Drift pin is designed to press the brake pad retaining pins back w/o damage to pin or caliper.
For a variety of brake applications. (overall length is 7 inches.)

Second tool LOWER RIGHT is the Spreader/Disc Brake Piston Reset Tool
This is a very useful tool for safe resetting of disc brake pistons on vehicles with fixed caliper disc brakes.

Brake Pad Spreader 14.99

Disk Brake Pad Spreader
Tool used for changing brake pads easy!
The tool compresses inner brake pad, resets piston for easy pad replacement.
Durable heavy duty construction.

Brake Caliper Rewind Set 47.99
U.S./EURO/ASIAN/4WD VEHICLES
Disc Brake Pad & Caliper Service Tool Kit
Includes 8 adapters Magnetic socket adapter.
For brake assemblies
For rotating pistons back into caliper to provide clearance for new pads
Prevents damage to the piston and bootDesigned for use with Mercedes, BMW, Volkswagen, GM, Audi, Ford,Honda, Subaru, Mazda, Nissan, Mitsubishi, Toyota, Land Rover and 4 wheel drive vehicles.Blow molded carryingcase for easy storage.
read more:

Disc Brake Piston Reset Tool 34.50

Very Useful tool , For safe resetting of disc brake pistons on vehicles with fixed caliper disc brakes.

Piston Ring Expander 0.00
Piston ring expanders, nickel plated, plastic coated handlesPressure on the handles opens the ring which is retained in the jaws by the side hooks. Once the pressure is released the ring enters into the piston groove.A transverse spring closes the tool when the piston ring is not inserted.
read more:

Nissan Turning Tool 12.50

Nissan tool, used for rotating the piston back into the rear brake caliperwhen replacing brake pads.Applicable: Nissan models, 81 with rear disc brakes.

Super Duty Disc Brake Tool 0.00
Heavy Duty Brake Tool
For safe resetting of disc brake pistons
on vehicles with fixed caliper disc brakes.
Extremely High Quality Tool Made in Germany.
Call for more info.
read more:

Brake Caliper Rewind Set 49.50

U.S./EURO/ASIAN/4WD VEHICLES
Disc Brake Pad & Caliper Service Tool Kit
Includes 8 adapters Magnetic socket adapter.
For brake assemblies
For rotating pistons back into caliper to provide clearance for new pads
Prevents damage to the piston and bootDesigned for use with Mercedes, BMW, Volkswagen, GM, Audi, Ford,Honda, Subaru, Mazda, Nissan, Mitsubishi, Toyota, Land Rover and 4 wheel drive vehicles.Blow molded carryingcase for easy storage.

PISTON PIN TOOL 0.00

FACTORY PISTON PIN TOOL USED TO REMOVE AND INSTALL PISTON PIN IN WATERBOXER ENGINES (1.9L & 2.1L)

14mm Brake Tool 34.99

14mm Hex Bit Brake Tool Ford Features:This unique tool has been developed to aid in the removal and installation of front disc brake calipers found on most 1984 and later Ford 6000, 7000 and 8000 CF series trucks. The use of this tool allows for quick and easy removal of the caliper without disassembling the front axle and steering arm assembly.Made from heat treated steel this tool comes in a black finish.

Brake Bleeder Kit 38.99
This Kit is one of the most useful products because it works for Automotive Motorcycle or ATV. Transform brake bleeding into a one hand, one person task. Makes a great motorcycle brake bleeder. Using the vacuum generated by the Mityvac pump, the user can draw out the brake fluid quickly and cleanly into a reservoir container. It bleeds hydraulic lines of most automotive brake systems, quickly and cleanly, including some anti lock brake systems (ABS). This kit contains the Mityvac Repairable Vacuum Pump, Reservoir Jar with Transfer Lid, Storage Lid, Brake Bleeding Adapter Package, 24 inches of 1/4" I.D. Tubing and our 110+ page Users Manual. Visit
read more:

Hazet Piston Ring Pliers 59.95

Piston Ring Pliers Made in Germany by Hazet! Tool used for 50 100 mm piston rings. The company HAZET was established in 1868 by Hermann Zerver. Today, the Plant 1 at Remscheid is one of the most advanced in Europe. HAZET WERK, the German tool manufacturer from Remscheid demands high standards offering a large range of hand tools and of special tools of highest quality which are especially suitable for the automotive engineering. What matters is the tool quality HAZET Quality is a guarantee for good work results.

Brake Gauge Made in Germany 00
Din 892, for measuring the thickness of disc brakes.
Stainless Steel with locking screw and trailing vernier scale (1/10mm) comes in a leather pouch.
Quality Stahlwille Tools!
This brake gauge measures the thickness of car and motorcycle brake discs in situ. When examining brake discs, refer to the manufacturers instructions. Measuring the thickness is simple using the brake disc gauge, and does not require the discs to be removed first!
read more:

T Handle Brake Hook 8.99

T Handle Brake Tool for mounting and dismounting thespring of brake shoes on vehicles with rear disk brakes.

Piston Ring Compressor 00
Piston Ring Compressor
For Mounting and removing Piston rings
Must specify size: For use on rings
50 to 100 , 80 to 120 , 110 to 160. Call for Availability.
read more:

12 Pack Air Tool Oil 19.99
12 Pack Air Tool Oil.
Specially Formulated for use in all piston type and rotary air tools, as well as in line air lubricators. Prevents rust formation while providing positive lubrication for smooth starting and longer tool life. Assures maximum performance by dissolving gum and sludge that cut down tool speed and reduce power output. ( Marvel 12 Pack)
read more:

Brake Tool 25.00

NUMBER 3289Brake Release Tool Volkswagen VR6 JettaTool is used to disconnect brake pedal from booster.This is an Original VW Factory ToolMade in Germany for Volkswagen By Kukko*

Brake Return Spring Tool 8.50

Brake return Spring Tool
Used to hook the return spring on vehicles without anchor pins.Excellent for the professional or shadetree mechanic!

12 Pack 32 oz Air Tool Oil 64.99
32 oz 12 Pack MVL085
Specially Formulated for use in all piston type and rotary air tools, as well as in line air lubricators. Prevents rust formation while providing positive lubrication for smooth starting and longer tool life. Assures maximum performance by dissolving gum and sludge that cut down tool speed and reduce power output. ( Marvel 12 Pack)
read more:

BRAKE TOOL 3343 0.00

ADJUSTMENT WRENCH USED WHEN ADJUSTING PARKING BRAKE. (REPAIR GROUP 46)

Deck Height Kit 29.95

This Tool measures the distance from the top of the cylinder to the top of the piston.
Proper deck height is essential in preventing the piston from hitting the cylinder head,
blue printing an engine and in calculating the compression ratio.
This easy to use tool measures deck height
with the use of its own calibrated, threaded screw or feeler guages,
dial indicators & calipers. It has been designed to allow the cylinder to be torqued
against the case for accurate measurement.
For use on type I, II, & III engines.

Factory Brake Caliper Tool 98.50
T10165 Brake Caliper Tool
The old number for this tool was 3272
(discontinued)
T10165 is the correct current factory number for this tool.
Brand New Tool
Made in Germany.
Some Vehicles include: Beetle 1.8 Turbo
(see your manual for exact year model applications tool number T10165 or old number 3272 same as T10165)
Beetle 4 CYL , Beetle TDI Diesel , Corrado SLC V6 ,
Golf Cabrio IV GL , Golf Cabrio IV GLX , Golf III GL 4 CYL ,
Golf III GTI 4 CYL , Golf III GTI VR6 , Golf III TDI Diesel , Golf IV 4 CYL ,
Golf IV GL 4 CYL , Golf IV GLS 4 CYL, Golf IV GTI 1.8 Turbo ,
Golf IV GTI VR6 AFP , Golf IV TDI Diesel , Golf IV VR6 AFP ,
Jetta III GL 4 CYL , Jetta III GLS 4 CYL , Jetta III GLX VR6 ,
Jetta III TDI Diesel , Jetta IV 1.8 Turbo , Jetta IV GL 4 CYL ,
Jetta IV GLS 4 CYL , Jetta IV GLS VR6 AFP , Jetta IV GLX VR6 AFP,
Jetta IV TDI Diesel , Jetta Wagon 1.8 Turbo , Jetta Wagon 1.9 TDI ALH ,
Jetta Wagon 4 CYL AZG / AVH, Passat TDI Diesel ,
Passat V6 30V AHA / ATQ , PassatTurbo 20V AEB
read more:

Caliper Tool 24.50

SPANNER SOCKET RR CALIPER USED TO TURN THE REAR BRAKE CALIPER PISTONS WHEN REPLACING BRAKE PADS

Caliper Tool 19.99

SPANNER SOCKET RR CALIPER USED TO TURN THE REAR BRAKE CALIPER PISTONS WHEN REPLACING BRAKE PADS

Brake Tool 8.99

BRAKE SPRING COMPRESSORFor removal and replacement of backing plate springs, cups & pins Pro style heat resistant handle Improved tip design grips parts more securely

Brake Caliper Tool 110.00

T10165 Brake Caliper Tool
The old number for this tool was 3272
(discontinued)
T10165 is the correct current factory number for this tool.
Brand New Tool
Made in Germany.
Some Vehicles include: Beetle 1.8 Turbo
(see your manual for exact year model applications tool number T10165 or old number 3272 same as T10165)
Beetle 4 CYL , Beetle TDI Diesel , Corrado SLC V6 ,
Golf Cabrio IV GL , Golf Cabrio IV GLX , Golf III GL 4 CYL ,
Golf III GTI 4 CYL , Golf III GTI VR6 , Golf III TDI Diesel , Golf IV 4 CYL ,
Golf IV GL 4 CYL , Golf IV GLS 4 CYL, Golf IV GTI 1.8 Turbo ,
Golf IV GTI VR6 AFP , Golf IV TDI Diesel , Golf IV VR6 AFP ,
Jetta III GL 4 CYL , Jetta III GLS 4 CYL , Jetta III GLX VR6 ,
Jetta III TDI Diesel , Jetta IV 1.8 Turbo , Jetta IV GL 4 CYL ,
Jetta IV GLS 4 CYL , Jetta IV GLS VR6 AFP , Jetta IV GLX VR6 AFP,
Jetta IV TDI Diesel , Jetta Wagon 1.8 Turbo , Jetta Wagon 1.9 TDI ALH ,
Jetta Wagon 4 CYL AZG / AVH, Passat TDI Diesel ,
Passat V6 30V AHA / ATQ , PassatTurbo 20V AEB

Brake Spring Plier 11.99

Brake Spring Tool for removing and installing Shoe return springs on most drum brakes. The socket end removes the spring from the anchor stud, and the notched end installs the spring on the anchor.

Honda Acura Bushing Tool Kit 189.00

Honda Acura Bushing Removal and Installation Tool easily and quickly removes and install trailing arm bushing in 15 minutes per side versus the factory "book" time of 1.8 hours per side. No removing the arm from the vihicle and using a hydraulic press. No need to disconnect brake parts such as calipers, rotors, shoes, lines or brake cables.
Works on Civic 1988 2000, CRX 1988 1991, Del Sol 1993 1997
Acura Integra 1994 2001

Drift Pin 18.50

Drift Pin 4mm Number P1045XDrift needed for removing disc brake pads.This Drift is designed to press the brake pad retaining pins backw/o damage to pin or caliper. Applicable: Porsche models.Also, for a variety of other applications.(Overall length of tool is 7 inches.)

Brake Guage 99.95

German Quality Caliper Gauge.
For Brake Disks on passenger cars and motorcycles.
Measuring range 60 mmjaw 75 mm.
Stainless Steel
Reading Parts: dull chrome.
(Also works on Mercedes same as MB number 140 589 0019 00). Quality tool made in Germany.

Digital Brake Gauge 99.95
Digital Brake Gauge
Features and Benefits:
Measuring range: 0 150mm / 0 6inchAccuracy: + 0.02mm / 0.001inchLCD display
Includes: One silver oxide battery SR44,1.55v
read more:

Piston Ring Compressor 13.99
WRINKLE BAND PISTON RING COMPRESSORLow friction wrinkle band fits 3" to 5" pistons Adjust only once for all pistons Easy to use
read more:

Top Dead Center Indicator 14.50
Top Dead Center Indicator9710 Used for T.D.C. on any Gas engine.Simply unscrew a spark plug and twist the rubber hosepart of this tool into the spark plug hole.As you rotate the engine with a turning bar,the piston forces air through the whistle part of this tool.Once the whistling stops the engine is at T.D.C.
read more:

Grease Fitting Rejuvenator Tool 46.50

Grease Fitting Rejuvenator ToolFeatures & Benefits:The Grease Fitting / Joint Opener will allow for a clogged grease fitting and/ or joint to take on grease by injecting a light viscosity oil into the greasejoint via the Zerk fitting, thus breaking up and removing any dirt, rust ordebris. The purpose of this tool is to free up the joint and the fittingenabling them to be greased.When using the tool, be sure to bleed any air out that may be trapped in thetool body. Once the tool is installed onto the grease fitting, only a tapping ofthe piston is required to open a joint.
Loosens hardened grease in joints
Opens clogged fittings
Warranty on the Grease Fitting Cleaner is limited lifetime
Wooden storage case
Flex hose
Large bore
read more:

10.75 Inch TDC Indicator 34.95

The TDC Indicator enables a technician to accurately setany piston to Top Dead Center. Just remove the spark plug, screw in the gauge and rotate the engine, observing the gradation markson the sliding shaft. Note the top of the piston stroke!. Accurately displays piston movement. 1/8" gradation marks. Installs as easily as a spark plug. Made of 1144 steel alloy with a stainless steel spring
10 3/4 (14mm thread): 7886
(ALSO AVAILABLE IN 6 IN. LENGTH)

6 Inch TDC Indicator 24.95

The TDC Indicator enables a technician to accurately setany piston to Top Dead Center. Just remove the spark plug, screw in the gauge and rotate the engine, observing the gradation markson the sliding shaft. Note the top of the piston stroke!. Accurately displays piston movement. 1/8" gradation marks. Installs as easily as a spark plug. Made of 1144 steel alloy with a stainless steel spring
6" Standard (14mm thread): 7880
(ALSO AVAILABLE IN 10.75 LENGTH)

Brake Caliper Brush 14.95
SK Facom
Heavy Duty Brake Caliper Brush
. Heavy duty steel wire.. Angled head for access.. Comfortable handle.
read more:

Long Handle Fuel Clamp 8.99

Long Handle Fuel Clamp
Quickly clamp off your brake and fuel lines while you do maintenance work. Smooth, rounded edges will not damage hoses. Easy operation, just a simple squeeze opens and closes.
For each brake line and the master cylinder to ensure minimal fluid loss and shorten bleeding time. Tool is 6 1/2 inches long.

The Beta Tank Tool Trolley 00
ItemCX25DescriptionTank trolley with compartmentSpecificationsMain features:Foldaway lid.1 sliding drawer.Tool tray protected by foamed rubber mats.Shelves protected by oil and fuel proof mats.Four castors 0 100 mm in 0:2 fixed and 2 swivelling (one with brake).Safety lock.One more shelf M4 can be added on the opposite side.Thermoformed tray for 1/2' sockets and accessories.Paper roll holder item 2499PC can also be included.Lower compartment, 290 mm high with 2 safety locks.Locking system of the lids in the open position.
read more:

7mm Super Stubby Hex 3/8 Drive 25.00

3/8 Drive Hex "STUBBY" 7mm
All the BMW People are after this tool.
Tool is exactly 1 inch long.
Hard to find and even harder to find at a good price.
Super Stubby 7mm Hex Socket for brake work on BMWs.
Drive size is 3/8.
(This tool is also available in a less expensive 1/4 drive
type in the number HEX7MM in the search button)
However most BMW people want this size (3/8).

Piston Ring Groove Cleaner 16.99

Piston Ring Groove Cleaner
Easily clean carbon and deposits from ring grooves. Comes with two wheels with five cutters for a total of 10 groove cleaning sizes.

Brake Bleeder Wrench 9mm 5.99

Offset Brake Bleeding Wrench 9mm x 7mm.

Top Dead Center Indicator 14.99

Top Dead Center Indicator9710 Used for T.D.C. on any Gas engine.Simply unscrew a spark plug and twist the rubber hosepart of this tool into the spark plug hole.As you rotate the engine with a turning bar,the piston forces air through the whistle part of this tool.Once the whistling stops the engine is at T.D.C.

Brake Bleeding Wrench 9mm 28.50

Brake Bleeding wrench 9mm. Made in Germany.

9 inch Brake Spoon 10.50

9 inch BRAKE SPOON. Drop forged steel. Chrome plated to resist corrosion.

Brake Bleeding Wrench Set 9.99

Offset Brake Bleeding Wrench Set
Size of wrench 9mm x 7mm and 8 x10mm. Excellent for the professional or shadetree mechanic.

You Searched for

Brake Piston Tool

Trade Links With ZDMAK